Feature Operations; Making Calls; Making A Call; Making A Call From The Phonebook List - Panasonic KX-UT113 Operating Instructions Manual

Feature Operations

Note
•
If KX-UT113/KX-UT123/KX-UT133/KX-UT136
is connected to a Panasonic KX-NS1000 PBX,
refer to the documentation of the KX-NS1000
for information about the operation of the unit.
However, please refer to this documentation for
details about the following features:
–
Phonebook (Page 25, 36)
–
Call Log (Page 26)

Making Calls

This section explains the basic methods for making a
call.

Making a Call

1.
In stand-by mode, go off-hook.
2.
Enter the number you want to call.
3.
Press [ENTER], or wait a few seconds for the
number to be dialed.
4.
To end the call, go on-hook.
Note
•
For KX-UT113/KX-UT123, if more than one line
is available at your unit, you can press
before going off-hook and then select the line
you want to use.
•
For KX-UT133/KX-UT136/KX-UT248, if more
than one line is available at your unit, you can
press an idle DN button (flexible button)
assigned to the line you want to use before
entering the number. For details about DN
buttons, see "Flexible Buttons (KX-UT133/
KX-UT136/KX-UT248 only) (Page 35)".
Pre-dialing
In stand-by mode, you can start dialing (max. 32 digits)
while still on-hook.
•
To delete a number you entered, press
•
To clear the entire number, press and hold
•
To connect the call, go off-hook or press [ENTER].
Note
•
For KX-UT133/KX-UT136/KX-UT248, you can
also press an idle DN button (flexible button) to
connect the call. For details about DN buttons,
Document Version 2012-02
see "Flexible Buttons (KX-UT133/KX-UT136/
KX-UT248 only) (Page 35)".
•
For KX-UT113/KX-UT123, when pre-dialing
you can press
If more than one line is available at your unit,
select the line to use, and then press [ENTER].
•
If you receive an incoming call during
pre-dialing, the display changes to the incoming
call screen. For KX-UT133/KX-UT136/
KX-UT248, you can close the incoming call
screen by pressing
pre-dialing.
Making a Call from the
Phonebook List
Scrolling through all entries
1.
Press
2.
Press [ ] or [ ] to select an entry.
3.
Go off-hook.
4.
To end the call, go on-hook.
Note
•
For KX-UT133/KX-UT136/KX-UT248, you can
also press an idle DN button (flexible button) in
step 3 to connect the call. For details about DN
buttons, see "Flexible Buttons (KX-UT133/
KX-UT136/KX-UT248 only) (Page 35)".
•
For KX-UT113/KX-UT123, you can press
Line
one line is available at your unit, select the line
to use, and then press [ENTER].
•
In step 2, if multiple phone numbers are stored
for the entry, you can press
select the phone number to call.
Searching by name
1.
Press
2.
Press
3.
Enter the name (max. 12 characters) you want to
search for.
.
4.
Press [ENTER].
Clear
The entry that matches your search appears.
.
Clear
5.
Go off-hook.
6.
To end the call, go on-hook.
Note
•
For KX-UT113/KX-UT123, you can press
instead of going off-hook.
Call
Close
.
instead of going off-hook. If more than
Call
.
.
Search
instead of going off-hook. If more than
Call
Operating Instructions
Feature Operations
, and continue
and then
Number
25