Toshiba Tosvert VF-AS1 Instruction Manual page 263

2. Basic parameter [2/4]
Communi
Title cation Function
No.
 0015 V/f control mode selection
0016 Manual torque boost 1

0014 Base frequency 1

0409 Base frequency voltage 1

0011 Maximum frequency

0012 Upper limit frequency

 0013 Lower limit frequency
 0009 Acceleration time 1
 0010 Deceleration time 1
RR/S4 input point 2
 0213
frequency
 0204 VI/II input point 2 frequency 0.0~ Hz
Preset speed operation
 0018
frequency 1
Preset speed operation
 0019
frequency 2
Preset speed operation
 0020
frequency 3
Preset speed operation
 0021
frequency 4
Preset speed operation
 0022
frequency 5
Preset speed operation
0023

frequency 6
Preset speed operation
0024

frequency 7
Forward run/reverse run
selection (operation panel
 0008
operation)
*1: Default values vary depending on the capacity.  See the table of K-48.
*2: Changing the parameter  enables to set to 0.01 sec. (adjustment range: 0.01~600.0 sec.).
*3: Inverter with a model number ending with -WN1: 60.0 -WP1: 50.0
Adjustment range
0:Constant torque characteristics
1:Voltage decrease curve
2:Automatic torque boost
3:Sensorless vector control 1 (speed)
4:Sensorless vector control 2 (speed/torque)
5:V/f 5-point setting
6:PM control
7:PG feedback control
8:PG feedback vector control
0.0~30.0%
25.0~500.0Hz
200V class:50~330V
400V class:50~660V
30.0~500.0Hz
0.0~ Hz
0.0~ Hz
0.1~6000 sec.
0.1~6000 sec.
0.0~ Hz
~ Hz
~ Hz
~ Hz
~ Hz
~ Hz
~ Hz
~ Hz
0:Forward run
1:Reverse run
2:Forward run (Forward/reverse switchable on operation
panel)
3:Reverse run (Forward/reverse switchable on
operation panel)
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum Vector control
Default Write during
setting unit
Speed
setting running
(Panel/Communi
control
cation)
-/-
-/-
●/-
●/-
1/1 0 Disabled ●/-
-/-
-/-
-/●
-/●
0.1/0.1 *1 Enabled -
0.1/0.01 *3 Disabled ●/●
1/0.1 *1 Disabled ●/●
0.1/0.01 80.0 Disabled ●/●
0.1/0.01 *3 Enabled ●/●
0.1/0.01 0.0 Enabled ●/●
0.1/0.1 *2 *1 Enabled ●/●
0.1/0.1 *2 *1 Enabled ●/●
0.1/0.01 *3 Enabled ●/●
0.1/0.01 *3 Enabled ●/●
0.1/0.01 0.0 Enabled ●/●
0.1/0.01 0.0 Enabled ●/●
0.1/0.01 0.0 Enabled ●/●
0.1/0.01 0.0 Enabled ●/●
0.1/0.01 0.0 Enabled ●/●
0.1/0.01 0.0 Enabled ●/●
0.1/0.01 0.0 Enabled ●/●
1/1 0 Enabled ●/●
PM
V/f Reference
Torque
control
control
-/- - ●
-/- - ●
-/- - -
-/- - -
●/- - - 5. 6
-/- - ●
-/- ● -
-/- - -
-/● - -
- ● ● 5. 7
●/● ● ● 5. 8
●/● ● ● 5. 8
●/● ● ● 5. 9
- ● ● 5. 10
- ● ● 5. 10
- ● ● 5. 2
- ● ● 5. 2
- ● ● 5. 11
- ● ● 5. 11
- ● ● 5. 12
- ● ● 5. 12
- ● ● 5. 12
- ● ● 5. 12
- ● ● 5. 12
- ● ● 5. 12
- ● ● 5. 12
●/● ● ● 5. 13