Table of Contents
Advertisement
EDITING
50
EN
DV Dubbing (HDD & DVD Deck Only)
You can dub programs from a camcorder or DV equipment
connected to the unit with a DV cable. The unit's remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
NOTE:
When connecting the unit to a device equipped with a DV input
connector, be sure to use the optional DV cable (VC-VDV 204U).
Your unit
Camcorder
DV equipment
The following on-screen display for DV dubbing appears when
ON SCREEN is pressed while the channel has been set to ADVB.
0:00
HDD
00:00:00. 00
FR360
12bit
DV
DV
A
A Remote control switch
To switch between the devices operable by the remote control
unit. The unit is operable when the remote icon (
displayed faces to the left, while the DV device is operable when
the remote icon is facing to the right.
B Auto capture button
Select to start or pause the dubbing. If ENTER is pressed when
the DV device is in the pause condition, preroll editing* where it
is possible to dub with a start time that is highly accurate will be
activated. When the DV device cannot be operated from the unit
(such as in camera mode), proceed with normal recording.
●
Do not start dubbing at the portion with no time code (A– –:– –:– –B).
* Preroll editing refers to the playback after the DV tape is slightly rewind.
(For DV devices that do not support the –1x speed, the rewinding time
may be longer.)
C Sound monitor switch
For selecting the desired sound format for dubbing.
To [DV IN/OUT]
DV cable
(VC-VDV 204U)
(not supplied)
DV connector
1:00
2:00
DV
GR-DV3500
00:00:00. 00
L – R
SOUND1
JVC
GR-DV3500
1 2
DV
B
C
)
1
Connect a camcorder or DV equipment to the [DV IN/OUT]
connector on the unit's front panel.
2
Press DV/HDD/DVD on the unit repeatedly; or press HDD or
DVD on the remote control to select the recording deck.
●
When dubbing to a DVD disc, load a recordable disc on this
unit.
3
Press INPUT SELECT +/– on the remote control or
INPUT SELECT on the unit to set the channel to ADVB.
4
Press ON SCREEN.
●
The on-screen display for DV dubbing appears.
5
Press selection keys to select
to display the remote icon (facing to the right) for the DV
equipment.
6
Press REC MODE repeatedly to set the recording mode. For
DV deck, press REC MODE on the remote control to set the
recording mode.
●
Each time you press REC MODE, the recording mode changes
as follows:
*1
N XP N SP N LP NEP N FR (60-360
DV
(Back to the beginning)
*
Selectable when dubbing to the HDD deck.
1
*
The value is selectable from 1 to 6 hours in 5 minutes interval by
2
D E
repeatedly after selecting AFR60–FR360B. To change
pressing
the value in 30 minutes interval, press and hold
For details on the recording mode, see ARecording ModeB
●
(A pg. 51).
7
Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: I, N, O, o, W.
●
To play back in slow speed (1/10 of the normal speed), press W
to pause playback, then press O or N.
●
To play back frame-by-frame, press W to pause playback, then
press W repeatedly. Each press of W advances a frame.
●
To change the playback direction, press O or N.
8
Press selection keys to select
repeatedly until the desired sound track appears on the TV
screen.
SOUND1
:
Select this to record the original stereo sound played back on
the connected DV equipment.
SOUND2
:
Select this to record the dubbed stereo sound played back on
the connected DV equipment.
MIX
:
Select this to record the sound of both ASOUND1B and
ASOUND2B.
●
Note that this selection is not available when the source
program is recorded in 16BIT (48 kHz) mode.
9
Press selection keys to select
ENTER. The dubbing starts.
●
Playback on the external DV equipment and recording on the
unit should start simultaneously.
●
To pause dubbing, press selection keys to select
then press ENTER. Both the unit and the external DV
equipment pause dubbing. Pressing W on the unit also works
the same way.
10
Press selection keys to select
ENTER. Then press o. The DV equipment stops.
11
Press selection keys to select
ENTER.
12
Press o twice on the remote control to stop dubbing.
●
Both the unit and the external DV equipment stop dubbing.
NOTES:
To create chapters (marks) automatically, set ADV AUTO
●
CHAPTERINGB to AONB. (A pg. 61)
●
Dubbing copyright guarded programs is not possible.
●
Original DV information such as the recording date and time are
not recorded.
●
The superimposed indication during the operation or dubbing is
not recorded.
, then press ENTER
*2
, 420, 480) N
D E
.
, then press ENTER
, then press
,
, then press
, then press
Hide quick links:
Advertisement
Table of Contents
