Live Memory Playback - JVC ShowView LPT0923-001A Instructions Manual

Live Memory Playback

Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Press HDD so that the HDD lamp lights up on the unit.
This unit records pictures onto the hard disc, instead of video
tapes, then plays back the pictures recorded on the disc. This
makes it possible to achieve high-speed writing and read-out that
has not been possible with conventional VCRs, enabling recording
and playback simultaneously.
High-speed spin
Recording
(High-speed writing)
Image figure of the hard disc
It is called "Live Memory Playback" to start playback of the
programme being recorded, with a time-lag between a recording
point and a playback point, as shown in the figure below.
Current playback point
(Live Memory Playback)
Recording start point
0 30 min.
Currently elapsed recording time
Not only can this unit play back a programme previously recorded
while recording or timer recording another programme, but the unit
also allows you to play back from the beginning of a programme
while continuing to record the same programme.
Temporary recording for Live Memory
This unit automatically records the channel being received, within
the specified range of time, to the reserved space on the hard disc.
The time range can be set for 30 minutes, 1 hour, and 3 hours.
( pg. 68)
NOTE:
Previous temporary recordings will be overwritten since the unit is
always recording the channel being received. Thus, it is not possible to
play back TV programmes recorded beyond the specified range of time
since they are already overwritten. To avoid this in order to save titles,
perform normal recording (
or Live Memory Recording (
About limitation on temporary recording
The temporary recording for Live Memory is cancelled in the
following cases, and will start all over again when it is to resume.
When the power is turned off
When the system is powered again after a power failure was
occurred
When normal recording, timer recording, Live Memory Recording,
or Automatic Satellite Programme Recording (
performed
When the "LIVE MEMORY" setting is changed (
When tuner channel setting is performed (
When dubbing is performed by pressing DUBBING (
When "DV" is selected by pressing PR +/– (
Playback
(High-speed read-out)
Current recording position
(Recording point)
Playback Recording
continues continues
1 hour
pg. 38), timer recording ( pg. 44, 46),
pg. 43).
pg. 48) is
pg. 68)
pg. 70)
pg. 58)
Recording/playback Status Display
NOTES:
Live Memory Playback cannot be performed for approximately 30
seconds after recording has started.
Although high-speed search up to approximately 30 seconds before
the current recording point is possible during Live Memory Playback,
once the current recording point is reached, the unit resumes normal
playback and maintains a delay of approximately 30 seconds so that
recording and playback can continue.
When using Live Memory Playback during timer recording, playback
continues even after the end of the recording.
When using Live Memory Playback during timer recording, playback
is automatically stopped just before recording starts, and then
recording starts when the time arrives for the next timer-programme.
It is impossible to perform ITR even if you press 7 during Live
Memory Playback. (
Press 8 to display the programme being recorded, then perform ITR
settings.
Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
Live Memory Playback cannot be performed while recording the
source from DV input. (
When LIVE CHECK is pressed to display the picture currently being
recorded, the picture size may not be correct.
Press 7 or LIVE to stop Live Memory Playback.
pg. 56)
BASIC OPERATIONS ON HDD DECK
CABLE/SAT
TV DVD
LIVE
ON SCREEN
Live Memory Playback status can be checked by
pressing ON SCREEN to display the bar meter on
the superimpose display. The current status is
superimposed on the TV screen. (
using Live Memory playback")
pg. 39)
pg. 58, "DV Dubbing")
41
EN
pg. 15, "When