Timer Mode - JVC HM-DR10000EU Instructions Manual

ENTER CHANNEL POSITION
6
Press TV PROG +/–.
SET TAPE SPEED
7
D-VHS mode:
Press STD/LS3 (
S-VHS or VHS mode:
Press SP/LP ( ) to set the tape speed.
SET VPS/PDC MODE
8
Press VPS/PDC to select "ON" or "OFF".
If "VPS/PDC ON" is displayed on the screen or "VPS/
PDC" is lit on the display panel, VPS/PDC is set to ON.
If "VPS/PDC OFF" is displayed on the screen or "VPS/PDC"
is not lit on the display panel, VPS/PDC is set to OFF.
"VPS/PDC Recording" in the right column.
RETURN TO NORMAL
SCREEN
9
After confirming all information is correct, press PROG
or OK. "PROGRAM COMPLETED" appears on the
screen for about 5 seconds, then normal screen
appears.
Repeat steps 1 – 9 for each additional programme.
ENGAGE RECORDER'S

TIMER MODE

10
Press ‰ (or ‰TIMER). The recorder turns off automati-
cally and ‰ appears on the display panel. The ‰TIMER
indicator on the recorder also lights up.
To disengage the timer, press ‰ (or ‰TIMER) again.
To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps 2 through 9, press WEEKLY (NUMBER
key "9") for weekly serials or DAILY (NUMBER key "8") for daily
serials (Monday – Friday). Either "WEEKLY" or "DAILY" appears
on the screen. Pressing the button again makes the correspond-
ing indication disappear.
NOTE:
You can programme this recorder to timer-record as many as 8
programmes. If you try to programme the recorder to record a
ninth, "PROGRAM FULL" appears on screen and "FULL" appears
on the front display panel. To record the extra programme, you
must first cancel any unnecessary programmes (
– P1 –
START STOP
=
21:00 22:00
SP(STD) VPS/PDC OFF
DATE TV PROG
25.12
ARD
[+/–] =
[PROG] : EXIT
SP
) to set the tape speed.
pg. 34).
Satellite Tuner Users
To timer-record a satellite broadcast using Express Timer
Programming:
1 Set "AV2 SELECT" to "AV2" or "SAT (
2 Perform steps 1 – 10. Select "L-1" or "L-2" for the
channel position in step 6, depending on the
connection to the satellite tuner (
3 Set the satellite tuner to the appropriate channel before
1
the selected programme begins.
4 Leave the satellite tuner's power on.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme
Delivery Control) and VPS (Video Programme System) are
service designed to assure safe, accurate timer recording.
With this system, special code signals are transmitted
together with the audio/video signals. These code signals
control your video recorder and have precedence over the
advertised times you may have preset into the timer. This
means that your recorder will start and stop recording when
the preset TV programmes actually start and end — even if
the broadcast time of a preset TV programme is changed.
NOTES:
When you use Express Timer Programming, set the start
time (VPS or PDC time) exactly as advertised in the TV
listing. A different time than advertised will result in no
recording.
VPS/PDC recording is also possible when a satellite tuner
or a cable system is connected to AV2 IN/DECODER on
your recorder.
VPS/PDC recording is also possible via the AV1 IN/OUT
connector.
How to check if the station being received transmits
a VPS/PDC signal
1 Press – –:– – until the channel position appears on the
display panel.
2 Hold down START+ for about 5 seconds.
"VPS/PDC" appears blinking on the display panel.
If a VPS/PDC signal is detected from the station , "VPS/
PDC" will stop blinking.
If no VPS/PDC signal is detected from the station , "VPS/
PDC" will blink at a slower rate.
3 Press – –:– – or START+ again to return to normal display.
33
EN
pg. 54).
pg. 57 – 59).