Video Plus+ Programming - JVC 3834RV0038A Instructions Manual

VIDEO Plus+ Programming

VIDEO Plus+ greatly simplifies entering the date,
channel, start and end times of a Timer Recording
by simply entering VIDEO Plus+ Code. VIDEO
Plus+ Codes are published in most TV guide mag-
azines; they can vary one to nine numbers in
length.
1. Make sure that TV channels have been tuned and
VIDEO Plus+
stored in correct
Insert a video cassette with protection tab into your
DVD+VCR.
REC
2. Press VIDEO Plus+.
3. Press the numbered buttons to enter the
PlusCode
of the TV programme that you wish to
record.
If you make a mistake press
revised number.
REC
4. Press OK.
If PLEASE CHECK is displayed it means that you
have entered the wrong
VIDEO Plus+ numbers
entered the
If "- -" is displayed, you have to enter the
programme number of the station, you want to
record from.
PR
PR-01
- -
- -
- -
- -
- -
- -
24
order.
VIDEO PLUS+ CODE NO.
- - - - - - - - -
0~9, OK i
F then enter the
VIDEO PLUS+ CODE NO.
246876543
DELETE :
0~9, OK i
VIDEO Plus+ numbers
incorrectly.
DATE TIME
12 10 : 11 11 55 ~ : SP
- - - - - - - - - - : ~ : SP
- -
- - - - - - - - : ~ : SP
- -
- - - - - - - - : ~ : SP
- -
- - - - - - - - : ~ : SP
- - - - - - - - - - : ~ : SP
- - - - - - - - - - : ~ : SP
i
5. Press F or G to select the settings that you wish to
revise. (PR, DATE, TIME VPS/PDC and SP).
Press D or E to enter the correct information.
6. Press G to select the recording speed.
Press D or E to select the desired tape speed
(SP, IP, or LP).
IP mode determines how much tape is left and
switches speed from SP to LP, if necessary, to
complete recording the program.
IP mode is not selected when VPS/PDC is ON.
Check that the timer event details are correct.
If you wish to record from AUDIO IN and VIDEO IN
on the front or from either of the EURO SCART
sockets on the back of VCR, press AUX to select for
correct display (AV1, AV2 or AV3).
7. If you want to make another VIDEO Plus+
recording repeat stages 2 - 7.
Press i twice.
If PLEASE CHECK is displayed, you have entered
incorrect information and will need to re-enter the
data.
Press 1 1 / / I to switch your DVD+VCR power off
,
mode.
will appear in the video recorder's display while
your VCR waits to make the recording.
To watch a DVD during timer recording standby
mode, press 1 1 / / I and DVD to switch to DVD mode.
8. Press 1 1 / / I to end recording.
Notes:
Programme Delivery Control (PDC)
The Programme Delivery Control (PDC) system adjusts
the start and end times of a timer record event. This can
be particularly useful with sports events which may run
over into extra time. The PDC signal is transmitted by
the broadcaster and this controls your video recorder's
timer. Currently only a limited number of TV companies
transmit PDC signals. Please make sure that when
recording from channels that do not broadcast PDC that
you turn PDC OFF.
PR DATE TIME
PR-01 12 SP
10 : 11 11 ~ : 55
- - - - - - - - - - - - : ~ : SP
- - - - - - - - - - - - : ~ : SP
- - - - - - - - - - - - : ~ : SP
- - - - - - - - - - - - : ~ : SP
- - - - - - - - - - - - : ~ : SP
- - - - - - - - - - - - : ~ : SP
i
PR DATE TIME
PR-01 12 10 : 11 11 ~ : 55 SP
- - - -
- - - - - - - - : ~ : SP
- - - -
- - - - - - - - : ~ : SP
- - - -
- - - - - - - - : ~ : SP
- - - - SP
- - - - - - - - : ~ :
- - - - - - - - - - - - : ~ : SP
- - - - - - - - - - - - : ~ : SP
i