Table of Contents
Advertisement
SAT S-VIDEO
:
If a connected satellite receiver's output is compatible with Y/C
signals, set to ASAT S-VIDEOB. You can obtain a high-quality
S-VHS picture. (For connection, be sure to use a 21-pin
SCART cable that is compatible with the Y/C signal.)
DECODER
:
To use a decoder connected to the [L-2 IN/DECODER] connector.
NOTES:
●
If you have a satellite receiver or a decoder connected to the [L-2
IN/DECODER] connector, be sure to set AL-2 SELECTB back to
appropriate mode after editing.
●
If you are not connecting a satellite receiver or a decoder to the
[L-2 IN/DECODER] connector, leave AL-2 SELECTB set to
AVIDEOB.
●
When AL-2 SELECTB is set to ASAT VIDEOB and ASAT S-VIDEOB,
ASATB appears on the TV screen or front display panel instead of
AL-2B.
●
If AL-1 OUTPUTB is set to ASCART S-VIDEOB, it is not possible to
set AL-2 SELECTB to ADECODERB or ASAT VIDEOB.
●
If AL-1 OUTPUTB is set to ASCART RGBB, it is not possible to set
AL-2 SELECTB to ADECODERB or ASAT S-VIDEOB.
●
If AL-1 OUTPUTB is set to ACOMPONENTB and AL-2 SELECTB to
ASAT VIDEOB, ASAT S-VIDEOB or ADECODERB, be sure to
connect the [L-1 IN/OUT] connector with a TV.
●
If AL-2 SELECTB is set to ASAT S-VIDEOB, be sure to set AL-1
OUTPUTB to ASCART S-VIDEOB.
F-1 Input Setting
Set AF-1 INPUTB to the appropriate mode depending on the
connector (VIDEO or S-VIDEO) being used on the front panel.
1
Perform steps 1 and 2 of AL-1 Output And L-1 Input SettingB
(A pg. 72).
2
Press F G to select AF-1 INPUTB, then press ENTER.
3
Press F G to select the
appropriate setting, then press
ENTER.
4
Press SET UP to complete the
setting.
* The boldface settings below indicate the settings at your purchase.
F-1 INPUT
VIDEO
/ S-VIDEO
^
8
VIDEO
:
When connecting an appliance to the [VIDEO] input connector,
set to AVIDEOB.
S-VIDEO:
When connecting an appliance to the [S-VIDEO] input
connector, set to AS-VIDEOB
DVD VIDEO SET UP
HDD/DVD SET UP
FUNCTION SET UP
REC/PLAY SET UP
DISPLAY SET
VIDEO IN/OUT
MONITOR TYPE
4:3LB
F-1 INPUT
VIDEO
L-1 OUTPUT
VIDEO
VIDEO
L-1 INPUT
SCART VIDEO
VIDEO
L-2 SELECT
ENTER
SET UP
SELECT WITH @ THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
EXIT
SELECT
.
Digital Audio Dubbing
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
However, it is not possible to dub copy-protected discs.
●
Turn on the TV and select the AV mode.
●
Slide the TV/CABLE/SAT/DVD switch to DVD.
Example: Dubbing to an MD
Player
INITIAL SET UP
VIDEO
S-VIDEO
Note for connection:
Remove the protection cap from the optical cable.
1
Connect the unit and a digital audio device using either an
optional optical cable or an optional coaxial cable.
2
Place a disc on the unit and load an MD on the connected
digital audio device.
3
Select the audio to be dubbed.
4
Start playback slightly before the actual point from where you
wish to start dubbing.
5
Press W to pause playback.
6
Select the input mode on the connected digital audio device.
7
Press I to start playback on the unit.
8
Start recording on the digital audio device.
9
Stop recording on the digital audio device. Then press o to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where
you intend editing to start, and where it actually starts.
EDITING
Recorder
Digital audio device
(MD deck, etc.)
Coaxial cable
Optical cable
(not supplied)
(not supplied)
To [DIGITAL
To [DIGITAL
AUDIO OUT
AUDIO OUT
(COAXIAL)]
(OPTICAL)]
73
EN
Rear of unit
Advertisement
Table of Contents
