Settings & Controls For Recording; Dvd Recording; Preparing A Disc For Recording; Pre-Recording Settings - JVC BD-X201M Instructions Manual

Jvc dvd recorder instructions
Hide thumbs Also See for BD-X201M:
Table of Contents

Advertisement

Settings & Controls for Recording

DVD Recording

DVD recording is carried out using the following procedure.

Pre-Recording Settings

● Insert a new DVD-R or DVD-RW (video mode) or alternatively, a similar disc that has
Preparation of the DVD-R or DVD-
been recorded on using the DVD recorder.
RW (video mode only).
● If the recording on a DVD-RW is to be performed once again from the beginning, erase
the disc's data using ERASE from the DISC MENU screen. (☞ Page 28)
Use the setting screens to select the appropriate recording signal, setup the recording
On-screen settings
conditions, and make other necessary settings. (☞ Page 29)
Audio recording levels can be adjusted in one of two different ways. (☞ Page 32)
Adjustment of audio recording levels.
The title and chapter menus are used during playback of a disc to select the section of
Selection of styles for the title and
the disc to be viewed. A total of five different display styles have been made available for
chapter menus
these menus, and these can be selected using the DVD MENU screen. In addition, the
DVD recorder also allows you to freely modify these display styles.
(☞ Page 35)
Recording Operations
● The section between the start of recording using the REC and PLAY buttons
Start of
and the end of recording using the STOP button constitutes a single recording
recording
Chapter 1
title, and each title is assigned a unique number.
A single disc can contain up to 99 different titles.
(chapter mark)
● Each title can be separated into a number of different chapters by inserting
chapter marks at the appropriate points. Unique numbers are also assigned
Chapter 2
to chapters, and a single title can contain up to 99 different chapters.
Title 1
● Adding chapters
If the REC button is pressed while recording, chapter mark and index will be
Chapter 3
inserted.
In addition, CHAPTER CREATION from the RECORDER MENU (1/2) screen
can also be used to setup the automatic or manual insertion of chapter marks
Chapter 4
and indexes.
End of
When the INDEX CREATION item on the RECORDER MENU (2/2) screen is
recording
(Title closing)
set to AUTO, indexes will be inserted automatically together with chapters at
Start of
recording
the record start point and recording pause point.
● Thumbnails (i.e., the frame at the start of recording) and backgrounds are
Chapter 1
automatically created for the title and chapter menus using the style selected
using STYLE from the DVD MENU screen.
Title 2
If EDIT MENU from the DVD MENU screen is set to ENABLE before the start
Chapter 2
of recording, it will be possible to modify the chapter menu's style and
thumbnails and to insert chapter names and comments whenever recording
End of
is stopped (i.e., whenever title closing is performed).
recording
● Once title closing has been carried out, it will not be possible to modify the
(Title closing)
Start of
chapter menu.
recording
● The REC CONTROL panel can be used to perform recording operations with
a keyboard. (REC CONTROL from the REMOTE MENU screen must be set
Title 3
to ON.)
● If EDIT MENU from the DVD MENU screen is set to ENABLE, it will be possible
End of
(Title closing)
recording
to modify the title menu's style and to input title names when the disc is being
finalized.
Processing After Recording
If additional recording is to be
If the disc is to be played on this DVD recorder or on a different DVD player:
performed:
Finalize the disc.
To do this, select FINALIZE from the DISC MENU screen.
Press the OPEN/CLOSE button and
remove the disc.
* When a disc has been finalized, it will not be possible to record more content to it or to
modify its menu styles.
26
(☞ Page 37)
(☞ Page 42)

Preparing a Disc for Recording

This DVD recorder is capable of recording to DVD-R and DVD-RW (in video mode).
DVD-R
: Only discs that conform with DVD-R Standard 2.0 (video mode) can be used.
DVD-RW : Discs of Version 1.1 or later can be used.
Although Version 1.1 of DVD-RW standards allows the selection of video mode and VR mode for recording, this
DVD recorder performs recording in video mode only.
* Version 1.0 of the DVD-RW standards does not support video-mode recording, and for this reason, the corresponding
discs cannot be used.
In terms of recording characteristics, DVD-R and DVD-RW (video mode) differ as follows.
DVD-R
: Each disc can be recorded only once. Erasing of data and re-recording are not possible.
DVD-RW (video mode)
: After viewing a disc, all data can be erased and it can be used to record new content.
The condition of the disc being used will dictate the available recording options as follows.
Disc condition
DVD-R
Blank disc
A disc recorded on using this DVD recorder
but not yet finalized.
Blank disc
DVD-RW
A disc recorded on using this DVD recorder
but not yet finalized.
A recorded disc from which data is to be
erased.
Notes
● If data has been erased from a disc using a different DVD recorder, it may not be possible to record new content to it using
this recorder. To avoid this type of situation, ensure that this DVD recorder is used to erase recorded data.
● New content cannot be recorded to discs that have been finalized.
It is possible to cancel the finalization and add a recording to a DVD-RW finalized on this machine.
● Regardless of whether or not finalization has been carried out, it will not be possible to use this DVD recorder to record new
content to a disc that has been recorded on using other devices.
Recording operations
New content can be recorded. A new title is created and recording
starts from that title's first chapter.
A new title is created in the unused section of the disc, and recording
starts from that title's first chapter.
New content can be recorded. A new title is created and recording
starts from that title's first chapter.
A new title is created in the unused section of the disc, and recording
starts from that title's first chapter.
Erase the recorded data (as described below), and then record
new content.
27

Advertisement

Table of Contents
loading

Table of Contents