NEC Univerge SV8100 Features And Specifications Manual page 960

Issue 1.0
Program
Program Name
Number
15-03-05 Single Line Telephone Basic Data
Setup – Trunk Polarity Reverse
15-03-06 Single Line Telephone Basic Data
Setup – Extension Polarity
Reverse
15-03-07 Single Line Telephone Basic Data
Setup – Enabled On-Hook When
Holding (SLT)
15-03-08 Single Line Telephone Basic Data
Setup – Answer On-Hook when
Holding (SLT)
15-03-09 Single Line Telephone Basic Data
Setup – Caller ID Function - For
External Module
15-03-10 Single Line Telephone Basic Data
Setup – Caller ID Name
15-03-11 Single Line Telephone Basic Data
Setup – Caller ID Type
15-03-14 Single Line Telephone Basic Data
Setup – Forwarded Caller ID
Display Mode
20-03-01 System Options for Single Line
Telephones – SLT Call Waiting
Answer Mode
20-03-02 System Options for Single Line
Telephones – Ignore Received DP
Dial on DTMF SLT Port
20-03-03 System Options for Single Line
Telephones – SLT DTMF Dial to
Trunk Lines
20-03-04 System Options for Single Line
Telephones – Dial Sending Start
Time for SLT or ARS
2 - 936
Description/Comments
-- Not Used in U.S. --Do Not
Change Default Entry as DTMF
issues may arise with voice mail.
-- Not Used in U.S. -- Do Not
Change Default Entry as DTMF
issues may arise with voice mail.
Used to Enable or Disable Enabled
On-Hook When Holding for SLT
terminals.
Used to Enable or Disable Answer
ON-Hook when Holding for SLT
terminals.
Enable (1) or disable (0) the Caller
ID FSK signal for an external Caller
ID module or a 3rd party vendor
telephone with Caller ID display.
Important:
If voice mail is used, this setting
must be disabled for the system
integration codes to be correct.
With a 2500 set (no Caller ID)
installed, this must be set to 0 for
incoming callers to have a talk path.
Determine if an extension user
telephone should display the Caller
ID name.
Determine whether the Caller ID
type is FSK or DTMF.
Determine what the display shows
when a multiline terminal receives a
forwarded outside call.
For a busy single line (500/2500
type) telephone, set the mode used
to answer a camped-on trunk call.
For ESL sets, enabling this option
(1) allows the user to dial Service
Code for Voice Mail Conversation
Record.
Use this option to define whether
the system should receive dial pulse
and DTMF signals (0) or ignore dial
pulse and only accept DTMF signals
(1).
Set the SLT phones to (0). Collect
all digits before sending or (1), send
out immediately after receiving.
When using a third-party external
paging device, set this option to 1.
In addition, set Program 20-03-04 to
1.
Set the time before the first digit is
sent out. When using a third-party
external paging device, set this
option to 1. In addition, set Program
20-03-03 to 1.
UNIVERGE SV8100
Assigned Data
0 = Off
1 = On
(default = 0)
0 = Disable (Off)
1 = Enable (On)
(default = 0)
0 = No
1 = Yes
(default = 1)
0 = Disable
(No)
1 = Yes
(Enable)
(default = 1)
0 = Disable
1 = Enable
(default = 0)
0 = Disable
1 = Enable
(default = 1)
0 = FSK
1 = DTMF
(default = 0)
0 = Calling Extension
Number (Calling)
1 = External Caller ID
(Forward)
(default = 0)
0 = Hookflash (Hooking)
1 = Hookflash + Service
Code 654
(default = 0)
0 = Do not ignore (No)
1 = Ignore (Yes)
(default = 0)
0 = Receive all digits, before
sending (All)
1 = Direct through out
(Direct)
(default = 0)
0~64800 (seconds)
(default = 1 second)
Single Line Telephones
Level
1 2 3