Summary of Contents for Siemens CHSL4010
-
Page 1: Installation Guide
CHSL4010 CHSL4011 Large Camera Housing Installation Guide Building Technologies Fire Safety & Security Products... - Page 2 Data and design subject to change without notice. / Supply subject to availability. © 2008 Copyright by Siemens Building Technologies We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.
-
Page 3: Table Of Contents
Adjusting the Sunshield ................11 Accessing the inside of the Housing Enclosure........11 Mounting the Camera and Lens Assembly..........12 Mounting the Camera Housing Assembly ..........13 Connecting to the Power Supply.............14 Maintenance and service ..............16 Disposal ....................16 Siemens Building Technologies Fire Safety & Security Products 09.2008... -
Page 5: Safety
Risk of cable damage due to stress Use only cable types that are approved for the environmental requirements. The cable glands used must be appropriate for the cable diameter. Siemens Building Technologies Fire Safety & Security Products 09.2008... -
Page 6: Meaning Of The Signal Words
There is a risk of minor to medium injuries or damage to property IMPORTANT Malfunctioning may result Meaning of the hazard symbols The nature of the hazard is indicated by icons. Warning of a hazard Siemens Building Technologies Fire Safety & Security Products 09.2008... -
Page 7: Eu Directives
EU Directives EU Directives The product complies with the requirements of the following EU directives. The EU declaration of conformity is available from: Siemens Building Technologies Fire & Security Products GmbH & Co. oHG 76181 Karlsruhe Germany EU Directive 2004/108/EC on electromagnetic compatibility... -
Page 8: Technical Data
Usable Height with Wiper fitted 88 mm Weight Including Sunshield: 6.0 Kg Excluding Sunshield: 4.9 Kg Suitable Pan and Tilt Units CDD2425, CDD2416-T, CDAP2316-T, CDAP2416-T Suitable Brackets CHBS2815, CDBS4540 + CAHA1040 Siemens Building Technologies Fire Safety & Security Products 09.2008... -
Page 9: Mechanical Dimensions
149 mm Key to Parts Fig. 2 Key to Parts Front End Cap Cable Anchor Housing Body Terminal Board Sunshield Camera Mounting Plate Rear End Cap Demister Assembly Cable Glands Window Siemens Building Technologies Fire Safety & Security Products 09.2008... -
Page 10: Scope Of Delivery
24 V AC Wiper Kit CAHL401X-WK Spare Wiper Arm Assembly CAHL4010-WU 230V AC Washer Unit CAHL4011-WU 24V AC Washer Unit CAPD1210-C230 12 V DC 500 mA PSU 230 V AC input Siemens Building Technologies Fire Safety & Security Products 09.2008... -
Page 11: Mounting
To re-assemble carry out steps 1 to 4 in reverse, making sure the earth wire is reconnected. The screws which secure the housing to the rear cap should be retightened to a torque of 2 Nm. Fig. 4 Inside the housing enclosure Rear End Cap Siemens Building Technologies Fire Safety & Security Products 09.2008... -
Page 12: Mounting The Camera And Lens Assembly
5.5 for details on connecting to the power supply. Use the cable anchors to clamp all cables. Once the camera installation and wiring is complete, close the housing as described in section 5.2. Fig. 5 Mounting the Camera and Lens Assembly Siemens Building Technologies Fire Safety & Security Products 09.2008... -
Page 13: Mounting The Camera Housing Assembly
Screw the mounting bracket to the base of the unit (A) (see Fig. 6). Secure the assembly following the bracket installation instructions. Fig. 6 Mounting the Camera Housing Assembly Siemens Building Technologies Fire Safety & Security Products 09.2008... -
Page 14: Connecting To The Power Supply
CAUTION building installation, protect the unit via a fuse or circuit breaker rated at 2 A for CHSL4010 110 – 230 V AC units and 5 A for CHSL4011 12 – 24 V AC units. NOTE Use only cable suitable for the application and that meets the standards required by the installation. - Page 15 Fuse F1 2 A 250 V AC 5x20 Type (T), HBC for T462 5 A 250 V AC 5x20 Type (T), HBC for T463 Heater Output (pre-wired and connected through fuse F1) Siemens Building Technologies Fire Safety & Security Products 09.2008...
-
Page 16: Maintenance And Service
Neither do they constitute or amend any earlier or existing commitment or legal relationship. All obligations on the part of Siemens result from the relevant purchase agreement which also contains the complete and solely valid warranty regulations. This installation guide neither extends nor restricts these contractual warranty regulations. - Page 18 Issued by Siemens Building Technologies Fire & Security Products GmbH & Co. oHG © 2008 Copyright by D-76181 Karlsruhe Siemens Building Technologies Data and design subject to change without notice. www.buildingtechnologies.siemens.com Supply subject to availability. Document no. A6V10087715 Edition 10.09.2008...