Related Manuals for Megalarm MEGA 474
Summary of Contents for Megalarm MEGA 474
-
Page 1: Alarm System
03282008 MEGA 474 DELUXE 3-CHANNEL ALARM SYSTEM Installation And Operation Manual MEGATRONIX CHATSWORTH, CA U.S.A. MEGA 470/474; VS 465/474L... - Page 2 03282008 MEGA 470/474; VS 465/474L...
-
Page 3: Wiring Diagram
03282008 WIRING DIAGRAM H7/3 Green Wire: (-) 200mA Lock Pulse H7 3 Pin White H1 5 Pin H1: Main 5 Pin White harness H7/1 Blue Wire: (-) 200mA Unlock Pulse White H6 2 Pin LED Indicator White H2 4 Pin Dual Zone Orange Shock... - Page 4 03282008 WIRING Keep wiring away from moving engine parts, exhaust pipes, and high-tension cable. To prevent fraying, tape wires that pass through holes on the firewall. Watch out for sharp edges that may damage wires and cause short circuit. CAUTION: Do not connect the wiring harness to the control module until all wiring to vehicle is complete. H1: MAIN 5 PIN WIRE HARNESS: H1/1.
-
Page 5: H4: Rf Antenna - Black Thin Wire (Do Not Cut!!!)
03282008 d). When the extend wires are needed, they must be exactly same gauge as the cut wire. Connect the cut wire from the key switch to the RED wire (pin #30) of the relay, and connect the starter wire to the WHITE wire (pin #87a) of the relay. - Page 6 03282008 VACUUM OPERATED CENTROL LOCKING 5-WIRE ALTERNATING DOOR LOCK Green Wire +12V Door Switch Green Wire Master Door Lock Switch Splice Cut the Existing 3 Pin Plug Unlock Wire +12V 3 Pin To Alarm Plug To Compressor Splice Alarm +12V Cut the Existing Lock Wire Blue Wire...
-
Page 7: Programming Transmitter
03282008 PROGRAMMING A. PROGRAMMING TRANSMITTER: Note: This unit will only retain the last 4 remote transmitters programmed. If the transmitter memory is full, the security system will start deleting transmitters from memory in chronological order. 1. Turn the Ignition switch ‘OFF/ON’ 3 TIMES and stay in the ON position. Within 15 seconds. 2. -
Page 8: Transmitter Operation
03282008 Exit : Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps to confirm exit. PASSWORD PIN CODE SETUP: 1. Turn the Ignition switch ‘ON/OFF’ 3 times and stay in the OFF position. 2. Push the Valet switch 8 times and hold it in on the 8 push until four chirps with a long chirp is heard. - Page 9 03282008 4 chirps Disarm / Intrusion 12 flashes Car Locator 6 chirps Car Locator E. ALARM OPERATING CONDITION: Siren Parking Light Doors Starter disable Pager 1. Arming 1 Chirp 1 Flash Slow flash Locking 2. Disarming 2 or 4 Chirps 2 or 3 Flashes Off or Fast flash Unlocking...
- Page 10 03282008 2. Within 5 seconds, enter your chosen 10ths digit by press and release the Valet Switch. (When finished above procedures, system's siren stop alarming, parking light stop flashing, but the vehicle cannot be start and drive away.) 3. Turn the ignition switch “OFF” position. [4] Chirps form siren/horn, [3] flash from parking light and LED will turn off to indicate the system was disarmed.
- Page 11 03282008 MEGA 470/474; VS 465/474L...
- Page 12 03282008 MEGA 470/474; VS 465/474L...
Need help?
Do you have a question about the MEGA 474 and is the answer not in the manual?
Questions and answers