Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Intelligent Home Cat-5 network cable
Summary of Contents for Intelligent Home Cat-5 network cable
-
Page 1: User Manual
Video Door Entry System for Flats / Aprtments user manual SPEAK DOOR OPEN SERVICE Cat-5 network cable user. Right to interpret and copyright of this manual are preserved. www.intelligenthomeonline.com www.intelligenthomeonline.com... -
Page 2: Warranty Card
WARRANTY CARD NB Please keep this document safe, as it is proof of your Warranty Your Video door system comes with a one year Manufacturers Warranty. When used normally, the following services are offered: The following actions will void the Warranty: 1. -
Page 3: Table Of Contents
Register patrol card ■ Press [CLR]→ Card number→ [F3]. Contents Delete single card ■ 1 System brief introduction ................................1 Card number delete： System introduction ................................. 1 Press[CLR]→ Card number→ [F4]. System features..................................1 Card reader delete： System function ..................................1 Press[CLR]→... -
Page 4: System Brief Introduction
1. System brief introduction Appendix 5. Remote control user manual System introduction Specifications: Battery: 3V (CR2025) C-5 system uses category 5 cable to transfer signal, it is very easy for system installation and maintenance. It adopts the automatic Available distance: ≤1 meters video pre-amplified and loss compensation technology to enable the stable signal transmission, this strength is more obvious in the long Angle: ≤30°... -
Page 5: Components
RJ45 plug making step pictures (Pictures in the table only for reference.) Components Step 1. Use clamp’s knife edge to cut needed length of Step 2. Remove the grey rubber protector, use knife the cable. edge to cut the cable trim Product Main features specifications... - Page 6 Appendix 4. RJ45 plug making method Product Main features Specifications Remark Firstly, introduce some tools and materials needed for making RJ45 plug. Indoor phone Achieve the functions of intercom, Unit equipment（basic） Operating voltage: DC30~35V; Quiescent current: ≤ 25mA; unlock, monitor, and sending alarm to One family can have 1-4 Operating current: ≤...
-
Page 7: System Wiring Diagram
■Indoor phone digit setting 2. System wiring diagram Door Station4 [Note] This information is used for setting the digit length of indoor Indoor Phone4 phone when perimeter gate station calls it. In P3 choose “Bit”, press [#] to confirm, LCD shows P21. Use number key to enter door station and indoor phone No.’s digit，... -
Page 8: Time Setting
3.Delete single card In P7, choose “Delete Single”, press [#], LCD shows P11, enter Delete Single Delete Single card No. according to hint, press [#] to confirm, or put card on No.: No. :0007234177 sensor of perimeter gate station, after successful deletion, shows P12. -
Page 9: Product Wiring Diagram
3. Product wiring diagram Under standby mode, press [F1], enter function main menu， Enter System System Password： Change PW _ _ _ _ shows as P1. This section will introduce wiring diagram for every parts’ port in detail. Help System setting Connection explanation In P1, choose “... -
Page 10: Switch Wiring Diagram
Switch wiring diagram Appendix 3. Perimeter gate station operation explanation Key Function: [F1]：To enter function menu and direction key(up). [1～9]：To enter figures or characters [F2]：Direction key(down ) [#]：Confirm key [F3]: Direction key(left)，public password unlocking [*]：Quit [F4]: Direction key(right)，resident password unlocking One port of switch can connect：1 perimeter gate station/ 1 guard unit/ 1 network spur track(which can connect at most for 63 gate-ways，adopts hand in hand connection method)/ 1 switch... -
Page 11: Gate-Way Wiring Diagram
Gate-way wiring diagram ■ Unlocking time In the menu of P3, input [4] + [#]. The LCD will show as P24. The right number shows current unlock time. It will change after input a new number, then press [#] button to confirm. (24) [Note] Unlock time is from 1s to 9S. -
Page 12: Distributor Wiring Diagram
Distributor wiring diagram V. Indoor phone data download In the menu of P8, input [5] + [#]. The LCD will show as P16. After finish, press [*] to back to P3 1. PORT1～PORT4 is used for indoor phone connection [Note] This function is for download the indoor phone information (16) 2. - Page 13 Door station extender diagram 1. Indoor phone setting In the menu of P3, input [1]+[#]，, the LCD will shows as P8, the 1. Door station should be set for busy mode: Switch off power, press the button 1 on door station then switch on power. After this, when information of indoor phone can be set here.
-
Page 14: System Setting
Door station lock diagram This door station has series of functions, and each function has [ # ] ：Confirm System provides two ways of electric lock connection for user to choose: Power unlock and signal unlock. (Note: For oversea market, its own function form. -
Page 15: System Programming
Appendix 2. LED door station operation explanation 4. System programming According to product wiring diagram, connect all the parts and then start system programming. Programming should follow the Restore Default Password [*] sequence from a building to network system. Programming products in a building first, then program system products in network. Building programming Door station [0+#] First step: Hardware setting... - Page 16 e.g.: Change password Enter System System PW Change PW Private PW Press [*] to back to P1, select “Change PW”, as P42 shows. Help Public PW Press [#] to confirm，enter P43. Status From the above form: the digit is=2＋4＋16＝22, so the distributer’s address/number is 022. (42) (43) ■...
- Page 17 (LCD door station) ■Time adjustment Step 2: Door station programming In P3, press [F1] or [F2] to select “Time & Date”, as P31 shows. 07-01-01 Time & Date Press [#] to confirm, LCD shows P32, set time according to hint, PW Unlock 00:00:00 1.
- Page 18 2. Door Station No. setting RegisterSingle ■Card registering Register Multi In P3, choose “Card”, LCD shows P22, here proceed IC/ID card Door station No. RegisterPatrol Select “door station” in the menu of P3, press [#] to confirm, then setting. 0001 Delete Single LCD shows as P8, input door station No.
- Page 19 After finish, back to P12，input next indoor phone No. or press [*] 3.Matrix input mode to back to P10. Start No.:_ _ _ _ [Note] This mode is only suitable for building with structure of matrix， if the [Note] 1. Ringing will be heard when indoor phone is called End No.
- Page 20 Step 3. Testing basic functions Door station No. ■Door station setting To test and check each device whether they work properly or not. 0 0 0 1 In P3, select “Door Station”, press[#]to confirm，LCD shows P8, Gate-Way Port : 1. Door station calling indoor phone here enter door station No.
- Page 21 (LED door station) This door station has series of functions, and each function has its [F1] ： Press this key to enter function form own function form. To enter function form, please press F1 key, Step 2: Door station programming dire ction key(up) press F1 or F2 key to roll and browse the function form, press [#] [F2]：Direction key (down)
- Page 22 3. Indoor phone setting Appendix 1. LCD door station operation explanation Door Station Single Input , input , the LCD will shows as P7, the In the menu of P2 information of indoor phone can be set here. Matrix Input I.Indoor phone digit Clear Data In the menu of P7, input...
- Page 23 IV. Indoor phone data upload 7. Trouble shooting [Note] This function is for upload indoor phone data saved in door station to gate-way when in network. In the menu of P7, input . The LCD will show as P13, Malfunction phenomenon Elimination method finally the LCD shows the upload result which is P14 A.
- Page 24 (Direct -call door station) Switch power, distributor, gate-way installation Product name Switch power Distributor Gate-way Step 2: Door station programming ■ Dip switch setting Adjust the switches (if there is) according to the follow illustration: 1.Gate-way ports setting PORT: [Door station 1] Dimension PORT: [Door station 2] 2.Buttons setting...
-
Page 25: Product Installation Explanation
Following setting especially for G9 door station (By remote control) 6. Product installation explanation First , you must enter the system setting: 1.Press [FN] +password(4 bits) +[ENTER] Door station installation 2.The door station will sound a long beep and the [DOOROPEN] LED will flash slowly. It means enter the system setting. [Note] Picture for reference only, please refer to the manual attached with door st ation for detailed installation . - Page 26 4. After finishing setup form, download it to switch, when download finishes, will show below: Network system programming According to building programming steps, have all door stations programmed, and then proceed network system programming. Successfully 0006 Bar Step 1. Perimeter gate station setting On standby mode, press F1 to enter main menu of P1, choose System Password：...
- Page 27 5. Data upload, after upload, show as below: 2. Setting guard unit No. Guard No:1 Seq. No.:0 15 New: Indoorphone.: 8 0 1 [Note] If there is only one guard unit in network, then the guard unit Distributor 0 0 5-1 number is 1.
- Page 28 System Programming Then proceed with perimeter gate station and guard unit setting. ■ Unit door station programming In P10，select setting equipment: 0: door station 1:guard unit First program first building 1.Type:Perimete 2:perimeter gate station Step 1: Hardware setting 2.No:0001 Example enter 2, and LCD shows P17 3.SwitchPort:00 （1）Set DIP of 4300 gate-way to 001 as below 4.Dist: 0...
- Page 29 System wiring diagram Step 3. Basic function tests 1. Perimeter gate station call guard unit Press # on perimeter gate station to call guard unit and guard unit answers. Malfunction 1, perimeter gate station shows: Fail-2. ● Che ck the wiring between perimeter gate station and switch. Malfunction 2.
- Page 30 Project case Malfunction 1 Customer requirement description 3. Intercom between indoor phone and guard unit Malfunction 1 Components 4. Perimeter gate station calling indoor phone Product Picture quantity / Lyra...
Need help?
Do you have a question about the Cat-5 network cable and is the answer not in the manual?
Questions and answers