Cabinet opening dimensions
25" (63.5 cm) countertop
(with or without backsplash)
24" (61 cm) base cabinet
countertop cutout depth 25" (63.5 cm)
Before you start...
Read electrical and carpentry instructions.
is your responsibility.
must install this range.
Make sure you have everything
It is the customer's
to make sure that the countertop
has been properly prepared and that the
clearances specified on the
rating plate are met. The
rating plate is located on the frame
behind the storage drawer.
where range will be installed.
The range should be located for convenient
in the kitchen. Recessed installations
provide complete enclosure of the sides and
rear of range.
IN THE WALL OR FLOOR
WHERE RANGE IS TO BE INSTALLED MUST
is for a 25-inch (63.5 cm)
countertop with a 24-inch (61 cm) base cabinet.
This appliance is
designed for use in a base cabinet with a depth
of 24 inches (61 cm). The maximum depth for
overhead cabinets is 13 inches (33 cm). For the
minimum vertical clearance between the
cooking surface and the overhead cabinets, see
Overhead cabinets installed at either
side of the appliance must be a minimum of 18
inches (45.7 cm) above the cooking surface.
The minimum horizontal distance between the
overhead cabinets is 30 inches (76.2 cm).
all governing codes
is required. See
30-3/8" (77.2 cm)
are shown must be
Do Not pinch the
power cord between
the range and the
4" (10.2 cm) min. 4
wall or other
or hinge opening.
Do Not seal range to
36" (91.4 cm)
Note: 30" (76.2 cm) min. when
of wood or metal cabinet
by not less than 114"
with not less than No. 28 MSG
sheet steel, 0.015" (0.4 mm)
steel, 0.024" (0.6 mm)
or 0.020" (0.5 mm)
36" (91.4 cm) min. clearance
the top of the cooking
and the bottom
wood or metal
WARNING: If the information
this manual is not followed
exactly, a fire or explosion may
result causing property
damage, personal injury or
- Do Not store or use gasoline
or other flammable vapors and
liquids in the vicinity of this or
any other appliance.
TO DO IF YOU SMELL
Do Not try to light any
Do Not touch any electrical
switch; Do Not use any
phone in your building.
Immediately call your gas
supplier from a neighbor's
phone. Follow the gas
If you cannot reach your gas
supplier, call the fire
- Installation and service must
be performed by a qualified
installer, service agency or the
Personal Injury Hazard
To eliminate the risk of burns or fire, avoid
installing cabinet storage above the
cooking surface. If cabinets are already
installed, reduce the hazard of reaching
over a heated cooking surface by
installing a range hood.The range hood
should extend a minimum of 5 inches out
from the bottom front of the cabinets.
Reaching over a heated cooking surface
could result in a serious burn or other
Electrical Shock Hazard
It is the customer's responsibility:
*To contact a qualified electrical installer.
*To assure that the electrical installation is
adequate and in conformance with
National Electrical Code, ANWNFPA
70 - latest edition* or CSA Standard
C22.1, Canadian Electrical Code,
Part 1 - latest edition"*, and all local
codes and ordinances.
Failure to do so could result in death or
The cooktop sides of the slide-in range fit over
the cutout edge of your countertop.
If you have a square finish (flat) countertop
and the opening width is 30-3/a" (77.2 cm),
ormed or tiled
(0.64 cm) back at
Formed front-edged countertops:
molded edge shaved flat l/4" (0.64 cm) from
each front corner of opening.
may need trim cut back
l/4" (0.64 cm) from each front corner and/or
rounded edge flattened.
If countertop opening width is greater than
adjust the l/4" (0.64 cm)
Place level on
first side to side; then front to back.
is not level, range will not be level.
Oven must be level for satisfactory
Mobile home installation
The installation of this range must conform to
Safety Standards, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home
and Safety, Title 24, HUD, Part
280); or when such standard is not applicable,
the Standard for Manufactured
and Setups), ANSI A225.1INFPA
501A*, or with local codes.
In Canada, the installation of this ranae must
conform with the current standards CAN/CSA-
or with local codes.
When this range is installed in a mobile home, it
must be secured to the floor during transit. Any
method of securing the range is adequate as
long as it conforms to the standards listed
The metal chassis of the range MUST be
in order for the con&o1 panel to
work. If the metal chassis of the range is not
NO keypads will operate.
Check with a qualified electrician if you are in
doubt as to whether the metal chassis of range
(4-s cm) beyond
(61 cm) base cabinet.
Copies of the standards listed may be obtained from:
M9W 1 R3
The floor anti-tip
with the range, see F
anel C and