Installation; Front Wiper Switch; Diagnosis And Testing - Front; Wiper/Washer Switch - Chrysler PT Cruiser Service & Repair Manual

PT
FRONT WIPER MOTOR - RHD (Continued)
(6) Remove the cowl cover. The right side cover
overlaps the left side cover, so they both must be
removed.
(a) Remove the rear engine compartment seal at
the cowl.
(b) Remove the four push retainers to the right
side cowl cover and remove from vehicle.
(c) Remove the three push retainers to the left
side cowl cover and remove from vehicle.
(7) Disconnect front wiper motor posi-lock harness
connector.
(8) Remove three front wiper module mounting
bolts (Fig. 14) and remove module from vehicle.
(9) Disconnect drive link from motor crank ball
joint.
(10) Remove three bolts to the front wiper motor
and separate from linkage.

INSTALLATION

(1) Place the motor on the wiper linkage and
install the three bolts to the front wiper motor.
(2) Connect drive link to motor crank ball joint.
(3) Place the front wiper module into cowl area
and install the three mounting bolts. Torque the
mounting screws to 8 N·m (75 in. lbs.).
(4) Connect the front wiper motor posi-lock har-
ness connector.
(5) Install the cowl cover. The right side cover
overlaps the left side cover.
(a) Place the left side cowl cover into position
and install the three push retainers.
(b) Place the right side cowl cover into position
and install the four push retainers.
(c) Install the rear engine compartment seal at
the cowl.
Before installation of the front wiper arms, activate
the wiper system to ensure the front wiper module is
in the PARK position. Position wiper arms so that
the tip of the driver's blade and the middle of the
passenger's blade is on the park line on the wind-
shield (Refer to 8 - ELECTRICAL/WIPERS/WASH-
ERS/WIPER ARMS - ADJUSTMENTS).
(6) Place the arm on the pivot while the arm is in
an over/centered position (Fig. 7).
(7) Install the wiper arm retaining nut (Fig. 7) and
torque to 21 N·m (190 in. lbs.).
(8) Install the wiper arm nut cap (Fig. 7).
(9) Connect the battery negative cable (Fig. 12).
(10) Close hood.
(11) Verify vehicle and system operation.
WIPERS/WASHERS

FRONT WIPER SWITCH

DIAGNOSIS AND TESTING - FRONT

WIPER/WASHER SWITCH

Refer to FRONT WIPER/WASHER SWITCH CON-
TINUITY TEST table and (Fig. 15).
FRONT WIPER/WASHER SWITCH CONTINUITY
MODE
OFF
LOW/MIST
HIGH
WASH
INTERMITTENT

REMOVAL

Fig. 15 WIPER/WASHER SWITCH CONNECTOR (C)
To service the front wiper/washer switch, the
multi-function switch must first be removed.
(1) Open hood.
(2) Disconnect and isolate the battery negative
cable (Fig. 12).
(3) Remove both upper and lower steering column
shrouds (Refer to 19 - STEERING/COLUMN/UPPER
SHROUD - REMOVAL).
(4) Disconnect both posi-lock harness connectors at
the rear of the multi-function switch (Fig. 16)
(5) Remove multi-function switch mounting screws
(Fig. 16)and remove switch from vehicle.
(6) Remove the two torx screws retaining the wip-
er/washer switch to the multi-function switch and
separate (Fig. 17).
INSTALLATION
To service the front wiper/washer switch, the
multi-function switch must first be removed.
(1) Place new wiper/washer switch next to the
multi-function switch and install two screws (Fig.
17).
(2) Place the multi-function switch into place and
install the two mounting screws (Fig. 16). Torque
multi-function switch to column retaining screws to 3
N·m (27 in. lbs.).
8R - 13
TEST
CONTINUITY BETWEEN
PIN C-1 AND C-6
PIN C-4 AND C-6
PIN C-4 AND C-5
PIN C-4 AND C-3
CANNOT BE CHECKED