Download Print this page

To The Installer; Important Note To The Owner Regarding Product Warranty; Replacement Parts; Unit Location - Whirlpool WGGE43 Installation Instructions Manual

Package gas electric furnaces
Hide thumbs

Advertisement

WARNING
Heating unit should not be utilized without reasonable,
routine inspection, maintenance and supervision. If the
Goodman 47
building in which any such device is located will be
vacant, care should be taken that such device is
routinely inspected, maintained and monitored. In the
event that the building may be exposed to freezing
temperatures and will be vacant, all water-bearing pipes
should be drained, the building should be properly
winterized and the water source closed. In the event
that the building may be exposed to freezing
temperatures and will be vacant, any hydronic coil units
should be drained as well, and, in such case, alternative
heat sources should be utilized.
CARBON MONOXIDE POISONING HAZARD
Special Warning for Installation of Furnace or Air Handling
Goodman 38
Units in Enclosed Areas such as Garages, Utility Rooms or
Parking Areas.
Carbon monoxide producing devices (such as an
automobile, space heater, gas water heater, etc.) should
not be operated in enclosed areas such as unventilated
garages, utility rooms or parking areas because of the
danger of carbon monoxide (CO) poisoning resulting from
the exhaust emissions. If a furnace or air handler is
installed in an enclosed area such as a garage, utility room
or parking area and a carbon monoxide producing device is
operated therein, there must be adequate, direct outside
ventilation.
This ventilation is necessary to avoid the danger of CO
poisoning which can occur if a carbon monoxide producing
device continues to operate in the enclosed area. Carbon
monoxide emissions can be (re)circulated throughout the
structure if the furnace or air handler is operating in any
mode.
CO can cause serious illness including permanent brain
damage or death.

TO THE INSTALLER

Before installing this unit, please read this manual to familiarize
yourself on the specific items which must be adhered to,
including maximum external static pressure to unit, air
temperature rise, minimum or maximum CFM and motor speed
connections.
4
DANGER
IMPORTANT NOTE TO THE
OWNER REGARDING
PRODUCT WARRANTY
Your warranty certificate is supplied as a separate document with
the unit installed by your contractor. Read the limited warranty
certificate carefully to determine what is and is not covered. Keep
the warranty certificate in a safe place. If you are unable to locate
the warranty certificate, please contact your installing contractor,
or contact customer service at 1-866-944-7575 to obtain a copy.
To receive the 10-Year Parts Limited Warranty, online registration
must be completed within 60 days of installation. Online
registration is not required in California or Quebec.
Full warranty details and instructions are available at
www.whirlpoolhvac.com.
To register your unit, go to www.whirlpoolhvac.com. Click on the
manufacturer's Comfort Commitment
the bottom center of the home page. Next, click on the Click
Here to Register Your Product link located at the top center of the
page, and complete the forms in the manner indicated.

REPLACEMENT PARTS

When reporting shortages or damages, or ordering repair parts,
give the complete product model and serial numbers as stamped
on the unit's nameplate. Replacement parts for this product are
available through your contractor or local distributor. For the
location of your nearest distributor, consult the white business
pages, the yellow page section of the local telephone book or
contact:
Tradewinds Distributing Company, LLC
14610 Breakers Drive
Jacksonville, Florida 32258
1-866-944-7575
If you are replacing an air handler, the system must be
manufacturer-approved and Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) matched.
NOTE: Installation of unmatched systems is strongly
discouraged.

UNIT LOCATION

WARNING
Goodman 50
To prevent possible equipment damage, property damage,
personal injury or death, the following bullet points must
be observed when installing the unit.
For proper flame pattern within the heat exchanger and
proper condensate drainage, the unit must be mounted level.
The flue outlet hood must be at least 12" (30.5 cm) from any
opening through which flue gases could enter a building, and
at least 36" (91.4 cm) above any forced air inlet located within
10 ft (3 m). The economizer/manual fresh air intake/motorized
fresh air intake and combustion air inlet mounted on the unit
are not affected by this restriction.
TM
Warranty link located at

Advertisement

loading

  Related Manuals for Whirlpool WGGE43