Electrolux E36IC75FSS Service Manual page 30

Icon designer series 36” induction drop-in cooktop
Hide thumbs Also See for E36IC75FSS:
Table of Contents

Advertisement

ELECTROLUX ICON 36" Induction Cooktop Error Codes
Error
Possible Cause or Condition
32
Low voltage output from 12V supply on
or
fi lter board in the 3 cook zone induction
72
module.
33
Improper voltage output from fi lter board in
or
the 3 cook zone induction module.
73
34
Communication failure between fi lter board
and power boards in the 3 cook zones
induction module / left side cooking zones.
35
AC input voltage too low in the 3 cook
or
zones
75
induction module.
36
Communication error between main touch
control and fi lter board.
(3 cook zones induction module / left side
cooking zones)
37
Heat sink temperature sensor break
(3 zones induction module / left side cook-
ing zones)
39
Confi guration mismatch between the User
Interface and the induction module (occurs
when one of the 2 zone induction modules
is replaced)
40
Communication failure between main touch
control and fi lter board.
45
Incoming power supply low voltage
51
LF Element temperature sensor break
52
LR Element temperature sensor break
53
Center Element temperature sensor break
54
RR Element temperature sensor break
55
RF Element temperature sensor break
60
Touch: general hardware error, keys
61
LF Element temperature sensor too hot
62
LR Element temperature sensor too hot
63
Center Element temperature sensor too hot
64
RR Element temperature sensor too hot
65
RF Element temperature sensor too hot
NOTE: If multiple changing error codes are displayed check for disconnected wires or cables.
-Test all cables & connections on fi lter circuit board in
the 3 zones induction module.
-Replace the fi lter circuit board in the 3 zones induction
module .
-Replace generator circuit boards in the 3 zones induction
module
- Check cable between fi lter board X12 and
generator board X10
- Replace the fi lter circuit board in the 3 zones induction
module .
- Replace generator circuit board in the 3 zones
induction module.
- Verify AC input voltage at the cooktop input.
- Verify AC main input cables, screws and jumpers.
- Replace the fi lter board in the 3 zones induction
module
- Verify all communication cables between user interface and both
- Replace the fi lter circuit board in the 3 zones induction module .
- Replace generator circuit board (dual) in the 3 zones induction
module .
-Replace the generator circuit board (LF/LRl) in the 3 zones
induction module
- To resolve this error, Press and hold WARM key, then press
Right Front zone ON key until beep (keep holding WARM)
release Right Front zone ON key and press Left Front zone ON
key until beep & confi g starts.
- Replace the fi lter circuit board in the 3 zones induction module .
- Verify AC input at the (2 zones induction housing) (X50 / X52).
- Verify Lin Bus harness cable from X68/X67 on right side fi lter
- Verify the lin communication wire at the timer input at
- Verify incoming power supply to cooktop
- Verify Element temperature sensor is correctly connected to the
generator circuit board.
- Replace element if temperature sensor resistor value is not
approximatively 1000 ohms (blue wires) at room temperature.
- Replace associated generator circuit board.
- Replace main power touch control.
- Replace cook zones touch controls
- Verify cooktop ventilation is correct (airway and fan).
- Verify Element temperature sensor is correctly connect to the
- Replace element if temperature sensor resistor value is not
approximatively 1000 ohms (blue wires) at room temperature.
- Replace associated generator circuit board.
Induction Cooktop Error Codes continued on next page
Page 30
Suggested Corrective Action
induction generator modules.
board (2 zones induction module) to X20 on the left side fi lter
board (3 zones induction module).
X4/X5 pin 2.
generator circuit board.

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents