Technical Data; Before Starting The Equipment; Assembly; Fitting The Additional Handle - Qualcast 30cc Original Operating Instructions

Petrol lawn trimmer
Hide thumbs Also See for 30cc:
Table of Contents

Advertisement

4. Technical data

Engine type:
2-stroke engine, air-cooled,
Engine power (max.):
Displacement:
Idle speed of engine:
Max. engine speed:
Max. twin line speed:
Ignition:
Drive:
Weight (with empty tank):
Long handle length:
Cutting circle diameter of line:
Cutting line length:
Cutting line diameter:
Tank capacity:
Spark plug:
Vibration ahv rear handle:
Uncertainty of vibration level:
L
sound pressure level:
pA
L
sound power level:
WA
Uncertainty sound level:
Sound and vibration were measured in
accordance with EN ISO 27917, 10884/7916.

5. Before starting the equipment

5.1 Assembly

5.1.1 Assembly of the long handle (Fig. D-E)
Remove the transport guard cap from the
lower long handle. Slacken the star grip screw
(Fig. D/Item A) on the connecting piece
on the upper long handle (Fig. D/Item B).
Carefully slide the lower long handle (Fig. D/
Item C) into the connecting piece on the
upper long handle.
When doing so, take care to ensure that
the drive shafts on the insides of the long
handles slide into each other (turn the spool
head gently, if required) and that the lock on
Helpline No. UK 0151 649 1500 / IRE 189 094 6244
the lower long handle (Fig. E/Item D) latches
securely in the connecting piece.
Now retighten the star grip screw (Fig. D/Item
A). To dismantle, proceed in reverse order.
chrome cylinder
0.76 kW/1.03 hp
5.1.2 Fitting the guard hood (Fig. F1–F2)
29.7 cc
Attach the safety guard to the lower long handle
2900 rpm
(Fig. F1). Screw the safety guard tightly in position
using the screw, washer and locknut (Fig. F2).
11000 rpm
8000 rpm
5.1.3 Fitting the carrying strap (Fig. G)
Electronic
The carrying strap is intended to help you
Centrifugal clutch
work safely and ergonomically with the petrol
grass trimmer. Hook the carrying strap into the
5.8 kg
fastening eyelet (Fig. G/Item 9).
135 cm
Check that all moving parts move smoothly
Ø 43 cm
before you start using the machine. Check
5.0 m
that all screws are securely fastened and also
check all the safety devices.
2.0 mm
0.6 l
5.1.4 Fitting the additional handle (Fig. G1–G3)
Slacken the wing nut on the fastening screw on
Torch L8RTC
the handle (Fig. G1/Item 1). Remove the nut
2
9.319 m/s
and the fastening screw (Fig. G1/Item 3) from
the handle clip the additional handle over
2
3.7m/s
the long shaft (Fig. G2). Insert the fastening
92 dB (A)
screw through the additional handle and then
112 dB (A)
clamp tightly by fitting the wing nut (Fig. G3).
1dB
5.2 Setting the cutting height
• Slip the shoulder strap (Fig. B/Item 17) over
• Set the length of the shoulder strap in such
Please note: Always use the shoulder strap
when using the machine. Attach the strap as
soon as you have started the engine and the
engine is running in idle mode. Switch off the
engine before you take off the shoulder strap.
Check the machine for the following each
time before use:
• That there are no leaks in the fuel system
• That the cutting unit and all safety devices
• That all screws are securely fastened
the left shoulder.
a way that the cutting head runs parallel
to the ground. In order to establish the
optimum length of the shoulder strap,
you should then make a few swinging
movements without starting the engine (Fig. I).
are in perfect condition
13

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Qg-pt 3043

Table of Contents