Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Installation Instructions for the Plug & Play Remote Start Package (EVOCHR5)
For JEEP Liberty 2008-2012
Review the remote start installation manual for safety instructions!
Overview
Your kit consists of two modules – a remote start and an EVO-ALL interface module. The EVO-ALL comes with a
plug and play t-harness and is designed to make the installation of the remote start very easy. There are a LOT of
wires in your kit. Because the EVO-ALL and remote start are designed to work together, you will use very few of
them. The only connections into the vehicle that are not direct plug-ins are the OPTIONAL parking light & hood pin
features.
STEP 1: Starting the installation
1. The bulk of the installation takes place right under the dash on the driver's side. Begin by removing the plastic
panel at the bottom of the dash, above where the pedals are. The panel is held in with both bolts and clips. Be
careful not to break the panel – especially in cold weather.
2. Install the on-glass antenna. Good locations for the antenna are at the top center of the windshield and along
side the driver's side windshield pillar. Tuck the wire inside the headliner and/or plastic molding and run it down
the underside of the dash, near the parking brake release. If you have side curtain air bags, be sure to route the
wire so it is behind the air bag, not in front of it. Plug the antenna into the remote start module.
3. We recommend permanently mounting the programming button. Use a ¼" drill bit to make a hole - the top of the
plastic kick panel on the left is a good location. Make sure that the switch and the wires do not interfere with the
parking brake. Plug the programming switch into the remote start module.
STEP 2: Plug in the T-Harness
1. Locate the immobilizer connector at the bottom of the key cylinder & disconnect the immobilizer connector
2. Connect the male connector of the T-harness to the immobilizer module
3. Connect the immobilizer connector to the female connector of the T-harness
1 |
P a g e
T6021 v1.1 02/2013
Advertisement
Related Manuals for Jeep Liberty 2008
Summary of Contents for Jeep Liberty 2008
- Page 1 T6021 v1.1 02/2013 Installation Instructions for the Plug & Play Remote Start Package (EVOCHR5) For JEEP Liberty 2008-2012 Review the remote start installation manual for safety instructions! Overview Your kit consists of two modules – a remote start and an EVO-ALL interface module. The EVO-ALL comes with a plug and play t-harness and is designed to make the installation of the remote start very easy.
- Page 2 STEP 3: Connecting the Remote Start & Bypass (See diagram on page 3) 1. Connect the pink wire from the remote start 6-pin power harness to the yellow wire on the 20-pin harness on the EVO-ALL (pin A1) and the loose yellow wire on the T-harness. *NOTE: Do NOT plug the 20-pin connector into the EVO-ALL yet, you will do this during the programming sequence 2.
- Page 3 P a g e...
- Page 4 STEP 4: Program The Bypass STEP 5: Finish up! Test all functions. After confirming that everything works properly, secure the remote start module and all the wires connected to it. Make sure none of the wires interferes with any of the moving parts under the dash. Replace the plastic panel that surrounds the ignition switch.
- Page 5 Installer’s Tips Tip #1 – Programming Options There are a variety of useful programming options available for your remote starters such as “engine run time”, “idle down timer”, etc. Instructions for how to program these options can be found on pages 15-16 of the installation instructions manual for your LCPRO remote start.
- Page 6 Use electrical tape to wrap the connection and secure the wires together. A wire tie will help prevent the tape from unraveling in the future. Method #3 – “T-Taps” T-taps are plastic clips that are squeezed onto the wires in the car. The wire from the remote start goes into the tap and the whole thing is crimped together.