Sony KP-43T70 Service Manual page 13

Connecting a DTV (digital television) receiver
Before connecting, be sure to read the
Operating Instructions of the DTV receiver.
1
Attach the coaxial cable from the roof
antenna to VHF/UHF on the DTV
receiver.
2
Using three yellow VIDEO cables,
connect Y, P and P of VIDEO OUT on
B R
the DTV receiver to Y, P and P
B
VIDEO 3 IN on the projection TV.
3
Using an AUDIO cable, connect AUDIO
OUT on the DTV receiver to AUDIO of
VIDEO 3 IN on the projection TV (White-
AUDIO Left, Red-AUDIO Right).
4
Set the DOWN CONVERTER ON/OFF
switch on the DTV receiver to ON.
Connecting a camcorder
Use this connection to view a picture directly
from your camcorder.
1
Using AUDIO and S VIDEO* cables,
connect AUDIO and S VIDEO OUT on
the camcorder to AUDIO and S VIDEO
IN inside the drop-down panel on the
front of the projection TV (White-AUDIO
Left, Red-AUDIO Right**).
2
Press VIDEO 2 to select the video inputs
from a camcorder.
* If your camcorder is not equipped with S
VIDEO, use a VIDEO cable (yellow) instead of
the S VIDEO cable.
** If you are connecting a monaural camcorder,
connect only the single audio output to the left
(MONO) input on the projection TV.
Installing and Connecting the Projection TV (continued)
Connecting two VCRs for tape
editing
By connecting a second VCR to MONITOR
OUT, you can record a program being played
by the primary VCR to the second VCR or
perform tape editing and dubbing.
1
Connect the VCR intended for playback
using the connection instructions on page
6 of this manual.
2
Using an AUDIO/VIDEO cable, connect
AUDIO and VIDEO IN on the VCR
intended for recording to AUDIO and
VIDEO OUT of MONITOR OUT on the
projection TV.
Notes:
• Do not change the input signal while
editing through MONITOR OUT.
• When connecting a single VCR to the
projection TV: if VCR LINE OUT is
connected to VIDEO IN on the projection
TV, do not connect MONITOR OUT on
the projection TV to the VCR LINE
INPUT (see right). Doing so will cause
program interference and other viewing
problems.
1 0
Y
P
B
P
R
IN
VIDEO 1 VIDEO 3
of MONITOR AUDIO
S VIDEO
R
VIDEO Y
L
P
B
(MONO)
AUDIO
R P
R
COMPONENT
(Rear of projection TV)
AUDIO-L AUDIO-R
VCR (for playback)
AUDIO R AUDIO L VIDEO
LINE
OUT
1
VMC-810S/820S
(not supplied)
– 13 –
Disconnect all power sources before making any connections.
VMC-10HG (not supplied)
AUX
TO
CONVERTER
DTV receiver
VHF/UHF
OUT
VHF/UHF
(VAR/FIX)
(DTV)
VIDEO
L
(MONO)
AUDIO
R
1
RK-74A (not supplied)
Roof antenna
YC-15V/30V (not supplied)
VIDEO
S VIDEO
AUDIO-L
AUDIO-R
L AUDIO R
VIDEO
S VIDEO
(MONO)
VIDEO 2 INPUT
(Front of projection TV)
Disconnect all power sources before making any connections.
(Rear of projection TV)
IN
VIDEO 1 VIDEO 3
OUT
S VIDEO MONITOR AUDIO
(VAR/FIX)
VIDEO Y
L
P
B
(MONO)
AUDIO
OUT
R P
R
IN
COMPONENT
VIDEO
VIDEO
AUDIO-L
AUDIO-L
AUDIO-R
AUDIO-R
(Rear of projectionTV)
VIDEO IN MONITOR
OUT
VCR
LINE
IN OUT
2
S VIDEO
VIDEO
1 2 Y R
DOLBY DIGITAL
AUDIO OUT
L
IN (OPTICAL)
(MONO)
P B G HD
DOWN
CONVERTER
R
ON/OFF
OUT
1 2 3 P R 4 B VD
CONTROL S
AUDIO OUT VIDEO OUT
4
3
Audio/
video
VMC-810S/820S
outputs
(not supplied)
S VIDEO
OUT
Camcorder
AUX
TO
CONVERTER
VHF/UHF
VIDEO
VCR (for recording)
L
(MONO)
AUDIO
AUDIO R AUDIO L VIDEO OUT
R LINE
IN
IN
2
VMC-810S/820S
(not supplied)
Indicates direction
of signal
9