Table of Contents
Advertisement
MENU SCREENS
OTHERS[2/2] Menu Screen
(Cont'd)
* This is not displayed in VTR mode.
Item
Function/Setting (bold characters indicate initial settings)
DR-HD100 A.OFF*
Selects whether or not to turn OFF the DR-HD100 (HDD unit by FOCUS enhancements) when this device is turned
OFF.
OFF
: Power does not turn OFF.
ON
: Power turns OFF with this device.
MEMO
• The [ mark is displayed at the upper right of the LCD monitor and viewfinder when the DR-HD100 is con-
nected. If this device is turned OFF before the mark is displayed, power does not turn OFF even if this setting is
ON.
• This setting is canceled and the DR-HD100 does not turn OFF in the following instances.
- 1394 REC TRIGGER item is set to OFF
- VTR mode is set
• When the DR-HD100 power turns off and this device is turned ON again, after 12 seconds, "DR-HD100 power?"
appears on the LCD monitor for 7 seconds.
MENU ALL RESET
Selects whether to reset the menu screen settings to initial settings.
The camera mode and VTR mode menu settings are reset. (The TC PRESET, UB PRESET, and CLOCK ADJUST
settings are not reset.)
CANCEL
: The settings are not reset.
EXECUTE : The settings are reset.
MEMO
• The cursor (K) does not move to this item when the VTR is activated.
• If the current menu settings and the factory settings have different FRAME RATE settings, "REBOOT!" is dis-
played for 3 seconds, this device automatically turns off and then turns on.
PAGE BACK
When the cursor is in this position, press the SHUTTER dial once to return to the OTHERS[1/2] menu screen.
DRUM HOUR
Displays the drum usage time.
Use as an estimate for regular maintenance.
The cursor (K) does not move to this item.
FAN HOUR
Displays the fan motor usage time.
Use as an estimate for regular maintenance.
The cursor (K) does not move to this item.
98
GENLOCK Menu Screen
Item
Function/Setting (bold characters indicate initial settings)
*1
SD H PHASE
Adjusts the horizontal (H) phase of the SD signal of this device according to the BB (Black Burst) signal input to the
[GENLOCK IN] terminal.
Increase the number
: Proceed horizontal phase.
Decrease the number : Delay horizontal phase.
[Settings: MIN, 31 to 1, 0, 1 to 86, MAX]
HD H PHASE
Adjusts the horizontal (H) phase of the HD signal and HD/SD SDI signal of this device according to the HD Tri-sync
signal input to the [GENLOCK IN] terminal. In addition, during Tri-sync signal input, H PHASE of SD analog signals
are simultaneously adjusted in HD H PHASE item.
Increase the number
: Proceed horizontal phase.
Decrease the number : Delay horizontal phase.
[Settings: MIN, 1023 to 1, 0, 1 to 1022, MAX]
MEMO
When adjusting the HD H PHASE, the setting value quickly changes while the USER1 or USER2 button is held
down for approximately two seconds.
*1
SC COARSE
Adjusts the phase of the subcarrier (SC) of the composite or YC separate signal of this device according to the BB
(Black Burst) signal input to the [GENLOCK IN] terminal.
Increase the number
: Proceed phase.
Decrease the number : Delay phase.
[Settings: 0°, 90°, 180°, 270°]
*1
SC FINE
Fine-tunes the phase of the subcarrier (SC) of the composite or YC separate signal of this device according to the
BB (Black Burst) signal input to the [GENLOCK IN] terminal.
Increase the number
: Proceed phase.
Decrease the number : Delay phase.
[Settings: MIN, 127 to 1, 0, 1 to 126, MAX]
PAGE BACK
When the cursor is in this position, press the SHUTTER dial once to return to the OTHERS[1/2] menu screen.
*1
REMOTE appears as the setting value of this item when the remote control unit is connected.
99
Advertisement
Table of Contents
