Audio Menu Screen - JVC GY-DV5001 Instructions Manual

11. MENU SCREENS

11-9AUDIO Menu Screen

Item
TEST TONE Sets whether or not the audio reference signal (1kHz, –20dBFS or
–12dBFS) should be output while the colour bar is output.
OFF: Audio reference signal is not output.
ON: Audio reference signal is output.
AUDIO MODE Selects the sampling frequency for audio recording (both CH-1 and CH-
2)
32K : Recording is performed with 12-bit, 32 kHz sampling frequency
48K : Recording is performed with 16-bit, 48 kHz sampling frequency
* The DV format offers recording tracks for up to 4 channel when using
12-bit, 32 kHz sampling. The GY-DV5000 records two of these track.
The GY-DV5000 does not allow after-recording.
A.OUT Selects whether or not audio should be output during search.
AT SEARCH OFF : Audio is not output
ON : Audio is output
CH1 FRONT Used to select whether or not the front section audio level control should
VR be operative. The front section audio level control only affects the audio
signal recorded on CH1.
DISABLE: Use of the front section audio level control is disabled.
ENABLE: Use of the front section audio level control is enabled.
* The operation of the CH-1 audio level control on the side section is
unaffected by this setting.
WIND CUT To select whether or not the low frequencies of the audio signal from the
audio input connectors are cut. Set to ON to reduce the wind noise of the
microphone.
OFF
FRONT : Only the low frequencies of the audio signal input to the FRONT
REAR : Only the low frequencies of the audio signal input to the REAR
BOTH : The low frequencies are cut for both the FRONT and REAR
AUDIO REF. Sets the reference audio level of the tape (both CH-1 and CH-2).
LEVEL –20dB : Records with –20 dB as the reference audio level.
–12dB : Records with –12 dB as the reference audio level. Use this setting
* Use the same setting for playback as for recording.
* This setting is unrelated to the audio level of the DV signal.
(GY-DV5001 only)
AUDIO Used to select which channels to reproduce when playing back a tape
SELECT with sound recorded on 4 channels. (Can only be set in the VTR mode.)
CH1/2 : To reproduce the sound recorded on CH-1 and CH-2.
MIX
CH3/4 : To reproduce the sound of the CH-3 and CH-4 channels.
MEMO:
The GY-DV5000 does not allow after-recording on the CH-3 and CH-
4 channels.
AUDIO Selects whether stereo sound or mixed sound is output from the PHONES
MONITOR jack when the MONITOR SELECT switch is set to MIX.
STEREO : Stereo sound (CH-1 audio is output from L, CH-2 audio is
* Only audio of CH-1 is output from the monitoring loudspeaker.
MIX
The TOP MENU screen returns when the SHUTTER dial is pressed while
PAGE BACK
the cursor is at this position.
E-74
Function
: Low frequencies are not cut.
AUDIO IN connector are cut.
AUDIO IN connector are cut.
AUDIO IN connectors.
when playing back the tape using DV equipment for general
consumer use.
The GY-DV5000 records audio on the CH-1 and CH-2 channels
during shooting.
: To simultaneously reproduce the sound of all four channels.
output from R)
: Mixed sound (The mixed CH-1 and CH-2 audio is output
from L and R)
Variation Range Initial Setting
OFF OFF
ON
32K 48K
48K
OFF ON
ON
DISABLE ENABLE
ENABLE
OFF OFF
FRONT
REAR
BOTH
–20dB –20dB
–12dB
CH1/2 CH1/2
MIX
CH3/4
STEREO MIX
MIX
––––– –––––