JVC 0303-MK-ID-SN Instructions Manual page 34

" SYSTEM" functions which are set when the Power
@
Switch is set to "
@
Power Switch is set to "
B EEP
T ALLY
R EMOTE
D EMO MODE
P R I OR I TY
C AM RESET
RETURN
BEEP
OFF: Even though not heard while shooting, shutter
sound is recorded on the tape.
BEEP: The beep sounds when the power is turned on
or off, and at the beginning and end of recording. Also
to activate the shutter sound effect (
[MELODY]: Instead of a beep, a melody sounds
when any operation is performed. It also activates the
shutter sound effect (
TALLY
OFF: The tally lamp remains off at all times.
[ON]: The tally lamp comes on to signal the start of
recording.
REMOTE
OFF: Disables the camcorder from receiving the
remote control's beam signals. The camcorder cannot
be operated by the remote control.
[ON]: Enables the camcorder to receive the remote
control's beam signals.
DEMO MODE
OFF: Automatic demonstration will not take place.
[ON]: Demonstrates certain functions such as
Programme AE with special effects, etc., and can be
used to confirm how these functions operate.
Demonstration starts in the following cases:
• When the Menu Screen is closed after "DEMO
MODE" is turned "ON".
• With "DEMO MODE" set to "ON", if there is no
operation for about 3 minutes after the Power Switch
@
is set to " " or "
Performing any operation during the demonstration
stops the demonstration temporarily. If no operation is
performed for more than 3 minutes after that, the
demonstration will resume.
NOTES:
If a tape is in the camcorder, the demonstration cannot be
turned on.
"DEMO MODE" remains "ON" even if the camcorder
power is turned off.
If "DEMO MODE" remains "ON", some functions will not
be available. After viewing demo, set to "OFF".
EN
34
USING MENUS FOR DETAILED ADJUSTMENT
SYSTEM
" are also applied when the
" ( pg. 35).
S Y S TEM
– MELODY
– ON
– ON
– ON
– LCD
pg. 17, 29).
pg. 17, 29).
" .
PRIORITY
[LCD]: When the LCD monitor is fully open, even if
the viewfinder is pulled out, the image is displayed
only on the LCD monitor; it will not be displayed in the
viewfinder.
FINDER: When the viewfinder is pulled out, even if
the LCD monitor is fully open, the image is displayed
only in the viewfinder; it will not be displayed on the
LCD monitor.
CAM RESET
[RETURN]: Does not reset all settings to the
factory-preset.
EXECUTE: Resets all settings to the factory-preset.
CAMERA DISPLAY
• Settings made in the "
are effective only for video shooting.
• Settings made in the "
remain effective even when the Power Switch
to " ". However, the menu settings can be changed
only when the Power Switch
C A
ON SC RE N
DATE / T
T I ME CODE
CLOCK
ADJ .
RETURN
ON SCREEN
LCD: Keeps the camcorder's display (except the date,
time and time code) from appearing on the connected
TV screen.
[LCD/TV]: Makes the camcorder's display appear on
screen when the camcorder is connected to a TV.
DATE/TIME
OFF: The date/time does not appear.
[AUTO]: Displays the date/time for approx. 5 seconds
in the following cases:
• When the Power Switch
or " ".
• When tape playback starts. The camcorder displays
the date/time when scenes are recorded.
• When the date is changed during tape playback.
ON: The date/time is always displayed.
• The date indication can also be turned on/off by
pressing the DISPLAY Button
control.
[ ] = Factory-preset
CAMERA DISPLAY" Menu
CAMERA DISPLAY" Menu
@
@
is set to " ".
M E R A D I SPLAY
E – LCD / TV
I ME – A U T O
– O F F
2 . 5 12 . 03
17 : 30
@
is set from "OFF" to "
U
on the remote
is set
"