Yamaha YZFR6X(C) 2008 Service Manual page 83

1. Clutch cable
2. Throttle cable (return side)
3. Throttle cable (pull side)
4. Right handlebar switch lead
5. Right radiator cover
6. Right upper side cowling
7. Right coupler holder
8. Right radiator fan motor lead
9. TPS lead
10.Throttle servo motor lead
11.Accelerator position sensor lead
12.Pickup coil lead
13.Ignition coil lead
14.Throttle body lead
15.Intake funnel servo motor lead
16.Rear brake light switch lead
17.O sensor lead
2
18.EXUP servo motor lead
19.Neutral switch lead
20.Fuel pump coupler
21.Fuel sender coupler
22.Fuel tank breather hose
23.Fuel tank drain hose
24.Battery negative lead
25.Engine ground lead
26.Sub-wire harness (secondary injector)
27.Oil level switch lead
28.Sidestand switch lead
29.Speed sensor lead
30.Starter motor lead
31.Left radiator fan motor lead
32.Left coupler holder
33.Main switch lead
34.Left handlebar switch lead
35.Radiator plate
36.Frame
37.Main harness
A. Route the clutch cable above the cover and
from the space next to the right coupler
holder to bottom of the vehicle.
B. Make sure that the throttle cable is not
twisted or crossed.
C. Route the throttle cable along the edge of
the protector on the return side of the throt-
tle cable and fit in the clamp on the cable
from upper side of the vehicle to the bot-
tom.
D. To the headlight.
E. Fasten the headlight harness and right
front turn signal light lead at the positioning
tape with a clamp.
F. To the front right turn signal light.
G. To the radiator.
H. Fasten the main harness, right radiator fan
motor lead, throttle position sensor lead,
throttle servo motor lead and accelerator
position sensor lead with a plastic locking
tie. Face the plastic locking tie to upward
and insert it into the hole of the right cou-
pler holder.
I. Route the right radiator fan motor lead
through the inside of the main harness.
There is no order for placing the throttle
position sensor lead and throttle servo
motor lead.
J. To the engine.
K. To the throttle body.
L. To the coolant temperature sensor.
M. Route the coolant temperature sensor lead
above the pickup coil lead, neutral switch
lead, oil level switch lead and speed sensor
lead.
N. Push the throttle body lead inward and
place the ignition coil lead coupler so that it
does not overlap or underlap with the throt-
tle body lead coupler.
O. The oil level switch lead, speed sensor
lead, pickup coil lead coupler and intake
funnel servo motor lead coupler should be
at inner and under the main harness.
There is no order for placing the neutral
switch lead.
P. Insert the plastic locking tie on the main
harness to the hole of the frame securely
so that it does not float.
Q. Route the neutral switch lead between the
frame and engine.
R. To the rear fender.
S. Install both the negative battery lead and
engine ground lead to the crankcase with
the bolt. There is no order for placing the
leads and install so that projection on each
lead are facing up. Route the oil level
switch lead and speed sensor lead under
the negative battery lead and engine
ground lead.
T. Sub-wire harness (secondary injector)
coupler must be under the main harness.
U. To the secondary injector.
V. Fasten the main harness and left radiator
fan motor lead with a plastic locking tie.
Face the tip of the plastic locking tie to
upward and insert it into the hole of the left
coupler holder.
W. Face the end of the plastic locking tie
inward, route the hole of the rectifier/regu-
lator bracket, then fasten the main har-
ness.
X. When turning the handle fullest to the right,
make sure that the left handlebar switch
lead is not strained.
Y. The left handlebar switch lead and main
switch lead can either be on top or bottom.
Z. Route the throttle cable through the right
side of the rib on the plate above the radia-
tor. Make sure that it is not twisted.
2-52
CABLE ROUTING