Martin MAC 350 Entour User Manual page 36

8-bit 16-bit
mode mode DMX Value
246 - 251
252 - 255
246 - 248
249 - 251
13 16
252 - 255
246 - 248
249 - 251
252 - 255
246 - 251
252 - 255
14 17
100 - 104
105 - 109
110 - 114
115 - 119
120 - 124
125 - 129
130 - 134
135 - 139
140 - 144
145 - 149
150 - 154
155 - 249
250 - 255
36
Percent Function
Effects speed
Shutter, focus
0 - 2 0 - 1 Tracking mode
Vector mode, fast → slow
3 - 245 1 - 96
96 - 98 Tracking mode
99 - 100 Vector mode, maximum speed
Color
0 - 2 0 - 1 Tracking mode
Vector mode, fast → slow
3 - 245 1 - 96
96 - 97 Tracking mode,
98 Tracking mode,
99 - 100 Blackout while moving
Gobo selection
0 - 245 0 - 1 Normal (no blackout)
1 - 96 Normal,
96 - 98 Normal,
99 - 100 Blackout while moving
Indexed gobo rotation (if indexed position selected on channel 4)
0 - 2 0 - 1 Tracking mode
Vector mode, fast → slow
3 - 245 1 - 96
96 - 98 Tracking mode
99 - 100 Blackout while moving
Fixture control settings (snap)
0 - 9 0 - 1 No function
10 - 14 2 - 3 Reset entire fixture
15 - 19 4 - 5 No function
20 - 24 6 - 7 Reset effects only
25 - 29 8 - 9 No function
30 - 34 10 - 11 Reset pan & tilt only
35 - 39 12 - 13 No function
40 - 44 14 - 15 Pan/tilt speed = NORM
45 - 49 16 - 17 Pan/tilt speed = FAST
50 - 54 18 - 19 Pan/tilt speed = SLOW
55 - 59 20 - 21 Reserved for future use
60 - 64 22 - 23 No function
65 - 69 24 - 25 Fan mode = Full
70 - 74 26 - 27 No function
75 - 79 28 - 29 Fan mode = Regulated
80 - 84 30 - 31 No function
85 - 89 32 - 33 Fan mode = Silent
90 - 94 34 - 35 No function
95 - 99 36 - 37 Dimmer curve = LIN
38 - 39 No function
40 - 41 Dimmer curve = SQR
42 - 43 No function
44 - 45 Dimmer curve = ISQR
46 - 47 No function
48 - 49 Dimmer curve = SCUR
50 - 51 No function
52 - 53 Calibrated output
54 - 55 No function
56 - 57 Raw output (maximum possible, non-calibrated)
58 - 59 No function
60 - 97 Reserved for future use
98 - 100 Illuminate display
Table 3: DMX Protocol
MAC 350 Entour user manual
SCUT OFF
= (overrides
SCUT ON
= (overrides
SCUT OFF ON
= (overrides
SCUT ON OFF
= (overrides
1
1
1
2
2
2
Channel Notes
2
1
2
menu, a reset command can only
be executed if channel 2 is set to
2
232 and channel 1 is set to zero.
2
2
affected by cycling power off/on.
2
2
2
2
ON
if set via control menu)
OFF
if set via control menu)
if set via control menu)
if set via control menu)
If DMX Reset is disabled in the
Menu override. Setting not
2