Download  Print this page

KYMCO Stryker 125 User Manual

Kymco stryker motorcycle user's manual.
Hide thumbs

Advertisement

Dear KYMCO Motorcycle Users:
Before the delivery of each new motorcycle, the fuel in carburetor is
drained off to ensure the excellent performance and safety of the
motorcycle. Therefore, when first starting a new motorcycle, it is
normal to take 20~30 seconds. The quality of each KYMCO
motorcycle is guaranteed.

Advertisement

Table of Contents

   Summary of Contents for KYMCO Stryker 125

  • Page 1 Before the delivery of each new motorcycle, the fuel in carburetor is drained off to ensure the excellent performance and safety of the motorcycle. Therefore, when first starting a new motorcycle, it is normal to take 20~30 seconds. The quality of each KYMCO motorcycle is guaranteed.
  • Page 2 Dear Users: STRYKER 125/150 We greatly appreciate your patronage of KYMCO This User‘s Manual describes the correct operating methods, inspection and STRYKER 125/150 maintenance procedures for the KYMCO details in order to prolong the service life of motorcycle and provide you with a comfortable riding.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS 1. PRECAUTIONS FOR A SAFE RIDING..............1 2. ASSEMBLY PARTS....................3 3. OPERATION INSTRUCTIONS................5 4. PRE-RIDE INSPECTION..................10 5. ENGINE STARTING METHODS ................. 19 6. NORMAL RIDING METHOD................22 7. PRECAUTIONS FOR RIDING ................24 8. HOW TO STOP RIDING ..................27 9.
  • Page 4: Precautions For A Safe Riding

    . PRECAUTIONS FOR A SAFE RIDING (1) CLOTHES To relax and wear comfortable clothes are the main points for a safe riding. To observe traffic laws, keep a cool mind, relax and be careful will provide you a safe riding. Wear helmet and fasten it tightly.
  • Page 5 (2) RIDING METHOD The safety of two-wheel vehicles is influenced by sitting position. The rider should sit on the central part of the seat cushion. If the rider sits on the rear part of the seat, the load of front wheel will decrease.
  • Page 6: Assembly Parts

    . ASSEMBLY PARTS Turn Signal Switch Fuel Tank Headlight Dimmer Switch L. Front Turn Signal Light Taillight/ Stoplight VIN (Vehicle Identification No.) L. Rear Turn Signal Light Engine Serial No. Tool Boxp Side Support Clutch panel - 3 -...
  • Page 7 Ignition Instruments Switch Starter Button R. Front Turn R. Rear Turn Signal Light Signal Light Exhaust Pipe Frame Serial No. Kick Lever Rear Brake Lever - 4 -...
  • Page 8: Operation Instructions

    3. OPERATION INSTRUCTIONS (1) IGNITION SWITCH/STEERING HANDLEBAR LOCK :At this position, power is connected to start the engine. The key cannot be taken out. :At this position, power is cut off and the engine stops. The key can be taken out. LOCK :At this position, the steering handlebar is locked.
  • Page 9 (2) STARTER BUTTON Release the steering handlebar lock before starting the engine. Turn on the ignition switch and then press the starter button. Make sure to depress the gear shift pedal into the neutral position to avoid engine damage. CAUTION: During engine running, do not push the starter button to avoid engine damage.
  • Page 10 HEADLIGHT DIMMER SWITCH/ PASSING SIGNAL SWITCH PASSING Switch to this position for using high beam. When riding in downtown area or there is a car coming from the opposite direction, use low beam to avoid affecting the visibility of coming cars. PASSING When passing, if there are cars coming from the opposite direction, press and switch and the...
  • Page 11 (6) TOOL BOX The tools in box are attached to this motorbike and you can put what you need in the rest space ,too. Max. loading capacity of the tool box is 1.5kg. (7) HELMET BUCKLE LOCK Insert the main switch key and turn it counterclockwise.
  • Page 12 (8) INSTRUMENTS MILEAGE COUNTER: The total riding mileage is indicated by kilometer. The figure in black and white is an unit of 100m. NEUTRAL POSITION INDICATOR LIGHT: When the engine is at the neutral position, this indicator light will come on when the ignition switch is ON.
  • Page 13: Pre-ride Inspection

    4. PRE-RIDE INSPECTION (1) ADVANCE INSPECTION Get into a good habit of inspection before riding. For the sake of safety and to prevent vehicle damage and traffic accidents, the pre-ride inspection is absolutely required. CAUTION: Be sure to perform inspection and maintenance for your new motorcycle after it is purchased for one month or ridden for 300km.
  • Page 14 (3) BRAKE INSPECTION Ride the motorcycle at low speed on a dry road Rear and respectively apply the front and rear brakes Brake to check the brake performance. The brake lever should have proper free play. “Free play” means the distance from the position of loose brake to the position of fully applied brake.
  • Page 15 2. CRACKS & DAMAGE Check the tire-contact area for crack or damage. 3. Abnormal Wear Check the tire-contact area for abnormal wear. 4. FOREIGN OBJECTS OF METAL PIECE & GRAVEL Check the tires and tire-contact area for imbedded objects of metal piece and gravel. 5.
  • Page 16 (5) FUEL LEVEL INSPECTION/REFILLING Check if the fuel is sufficient. If the fuel gauge pointer is at “E” (red line), refill #92 or #95 nonleaded gasoline as soon as possible. Refilling Method 1. Open the fuel tank cap protective cover. Insert the ignition switch key into the fuel tank cap lock and turn the key counterclockwise to unlock and open the cap.
  • Page 17 (6) STEERING HANDLEBAR Visually inspect the steering handlebar for damage. Apply the front brake and move the handlebar upward and downward to check for abnormal noise. Move the steering handlebar upward, downward, rightward and leftward to check for any loose parts.
  • Page 18 (8) BRAKE LEVER FREE PLAY INSPECTION & ADJUSTMENT Adjust the brake lever free play with the brake adjusting nuts. After adjustment, fully apply the brake levers and check if the free play is within the specified value (lever1~2cm). Increase play Decrease play CAUTION: After the brake is adjusted, align the groove of...
  • Page 19 (10) HORN/LIGHTS INSPECTION Turn the ignition switch “ON” and press the horn button to check if it sounds. Headlight/Taillight Inspection: Start the engine and turn on the headlight switch to check if the headlight and taillight are good and check the light shells for dirt and damage. Stoplight Inspection: Apply the front and rear brake levers respectively to check if the stoplight is good.
  • Page 20 (11) CLUTCH LEVER FREE PLAY INSPECTION The clutch lever free play shall be 1~2cm. Often check the clutch lever free play and make necessary adjustment by turning the adjusting nut. Free Play 1~2cm Lock Nut Adjusting Nut CAUTION: If the clutch lever free play is too big or small, the clutch disk will be damaged easily.
  • Page 21 (13) FRONT/REAR SHOCK ABSORBER INSPECTION Check the condition of the front/rear shock absorbers by pressing down on the handlebar and seat several times. (14) BRAKE PERFORMANCE INSPECTION Fully apply the front and rear brake levers and move the motorcycle forward to see if the braking effect is good.
  • Page 22: Engine Starting Methods

    5. ENGINE STARTING METHODS (1) TURN THE IGNITION SWITCH “ON” Unlock the steering handlebar. Before starting the engine, please rebound the side stand. Safety Installation. CAUTION: Check the gasoline volume and engine oil level before starting the engine. (2) USE NEUTRAL POSITION The engine must be started in the neutral position.
  • Page 23 (3) USE THE STARTER BUTTON Push the starter button without rotating the throttle grip. If the engine fails to start after the starter button is pressed for 3~4 seconds when it is warm, rotate the throttle grip for 1/8~1/4 turn to facilitate starting.
  • Page 24 START WITH THE KICK LEVER 1. Place the motorcycle on its main stand on level ground. 2. Depress the kick lever with force. When the engine is cold and does not start after the kick lever is depressed for 3~4 times, rotate the throttle grip for 1/8~1/4 turn to facilitate starting.
  • Page 25: Normal Riding Method

    6. NORMAL RIDING METHOD (1) REBOUND THE SIDE STAND Keep the engine in the neutral position and support the motorcycle upright, then the side stand will rebound automatically. CAUTION: After starting the engine and before moving, do not turn the throttle grip to increase the engine rpm.
  • Page 26 (3) CORRECT SITTING POSITION Ride astride on the motorcycle from the left side and sit upright. Touch the ground with left foot to avoid slipping. CAUTION: The rider must wear helmet and fasten the safety belt securely. Do not wear any loose clothes which will affect riding safety.
  • Page 27: Precautions For Riding

    7. PRECAUTIONS FOR RIDING CORRECT RIDING Before moving, turn on the turn signal light and make sure whether the rear side is safe. Do not rush into the car lanes and always keep the motorcycle to the right to avoid danger. CAUTION: Moderate riding will prolong the engine service life.
  • Page 28 (3) PROPER RIDING WILL PROLONG THE SERVICE LIFE OF ENGINE For a new motorcycle, keep the speed below 60km per hour within the first 1000km of riding. Avoid sudden acceleration and long-time riding at high speed. In hot weather, the engine overheats easily at long-time idling.
  • Page 29 (5) DO NOT MAKE SUDDEN STOP OR SHARP TURN Sudden stop and sharp turn are the main causes for slipping and could be very dangerous. In rainy days the road is slippery. Sudden stop will cause the motorcycle to slip. Be careful to avoid danger.
  • Page 30: How To Stop Riding

    8. HOW TO STOP RIDING (1) WHILE GO NEAR THE PARKING PLACE Turn on the turn signal light in advance. Watch out vehicles coming behind or aside and stop the motorcycle to the right side slowly. Restore the throttle grip to closed position and apply the front and rear brakes as early as possible.
  • Page 31 (3) PARKING Place the motorcycle on its main stand on level ground and do not hinder the traffic. Stand on the left side and grip the handlebar straight with left hand and the side rod or rear carrier with right hand. Then, put down the side stand by your right foot.
  • Page 32: Easy Maintenance

    9. EASY MAINTENANCE (1) AIR CLEANER INSPECTION AND AIR CLEANER CLEANING & REPLACEMENT Take out the air cleaner and visually check if it is dirty or clogged. 1. Remove the screws attaching the air cleaner cover and remove the air cleaner cover. 2.
  • Page 33 (2) FUEL SYSTEM Fuel Leakage Inspection Check the fuel line between the fuel tank and carburetor for fuel leakage. Fuel tube connector Fuel tank CAUTION: Check and replace any broken or damaged tube connector to avoid breakdown due to running out of gasoline.
  • Page 34 (4) BATTERY This model adopts the battery which needs no refilling of distilled water. When cleaning the terminal terminals, remove the screws attaching the battery cover on the floor board and then open the battery cover. When battery terminals are corroded, take out the battery for cleaning.
  • Page 35 (5) FUSE CHANGE Turn off the main switch and check if the fuse is burned out. When the fuse is burned out, replace with a specified fuse. Check for the cause of breakdown before replacing. Fuse Specification: 15A Fuse CAUTION: Be careful not to excessively expand the fuse clip during removal.
  • Page 36 (6) ENGINE OIL CHANGE 1. Place the motorcycle on its main stand on level ground. 2. Remove the oil dipstick. 3. Remove the drain bolt to drain the oil. 4. Refill fresh engine oil for 0.9 liter. Firmly tighten the oil dipstick. 5.
  • Page 37 (7) SPARK PLUG INSPECTION Check the spark plug side electrodes for wear. Fouling deposits on spark plug electrodes and big gap may result in weak spark. Spark Spark Plug Removal: 1. Remove the spark plug with a spark plug remover. 2.
  • Page 38 (8) BRAKE FLUID LEVEL INSPECTION /REFILLING Remove the 2 screws from the brake fluid tank and take off the cover. Add recommended brake fluid DOT-3 into the tank until the fluid level reaches the upper limit and then put on the cover and tighten the screws. Recommended Brake Fluid: DOT-3 CAUTION: Do not mix brake fluid of different brands.
  • Page 39: Important Notices

    Is the way to start the engine correct? Is there any other faulty parts? (2) IN CASE OF BREAKDOWN For any trouble occurred during riding, go to a KYMCO distributor or service station for inspection. CAUTION: For the sake of safety and to prevent vehicle damage and save your precious time, the pre-ride inspection is absolutely required.
  • Page 40 (3) POLLUTION-FREE PERIODIC MAINTENANCE SCHEDULE In order to have a safe riding, maintain good performance, prolong the motorcycle service life and reduce pollution, make sure to perform the periodic inspection and maintenance. I: Inspect and clean, lubricate, refill, repair or replace if necessary. A: Adjust C: Clean R: Replace T: Tighten Regular Service Mileage (KM) Daily Pre-ride...
  • Page 41 (4) EXPLAINATION FOR ACTION OF SAFETY INSTALLATION 1.MOTOR CAN BE STARTED WHILE ENGINE IS IN NEUTRAL POSITION. - 38 -...
  • Page 42 2.MOTOR CAN BE STARTED WHILE SIDESTAND SWITCH IS BEING KIKED ON AND CLUTCH SWITCH IS ACTING - 39 -...
  • Page 43 3.CDI CAN BE STARTED WIHLE ENGINE IS IN NEUTRAL POSITION - 40 -...
  • Page 44 4.CDI CAN BE STARTED WHILE SIDE STAND SWITCH IS BEING KIKED ON - 41 -...
  • Page 45 (5) SPECIFICATIONS ( DA25AA . DA25AB ) OHC air ooled 4- Engine Type Overall Length 2120 mm stroke single cylinder Displacement 124 cc Overall Width 880 mm Bore x Stroke 56.5x49.5 mm Overall Height 1300 mm Compression Ratio 9.2 : 1 Dry Weight 127 kg Max.
  • Page 46 ( DA30AA . DA30AB ) OHC air cooled 4- Engine Type Overall Length 2120 mm stroke single cylinder Displacement 149.4 cc Overall Width 880 mm Bore x Stroke 62x49.5 mm Overall Height 1300 mm Compression Ratio 9.7 : 1 Dry Weight 127 kg Max.

This manual is also suitable for:

Stryker 150

Comments to this Manuals

Symbols: 0
Latest comments: