Pelican PRO-RO Performance Data Sheet

Pelican PRO-RO Performance Data Sheet

6-stage reverse osmosis system

Advertisement

PRO-RO
6-Stage Reverse Osmosis System
System tested and certified by NSF International
against NSF/ANSI Standard 58 for the reduction of
substances specified on the performance data sheet.
Pelican Water Systems
Rev: 0814
877-842-1635, www.pelicanwater.com
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PRO-RO and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Pelican PRO-RO

  • Page 1 PRO-RO 6-Stage Reverse Osmosis System System tested and certified by NSF International against NSF/ANSI Standard 58 for the reduction of substances specified on the performance data sheet. Pelican Water Systems Rev: 0814 877-842-1635, www.pelicanwater.com...
  • Page 2 Please fill out the following information at the time of installation. Save for future reference. Pelican PRO-RO Model: Date Code: Install Date: Sold by: Installed By: Service Center Phone Number:...
  • Page 3 Nimbus recommends replacing the membrane when TDS reduction falls below 75%. In order to ensure the system is functioning properly, a water sample must be sent in to Pelican every 6 months for a free di- agnosis of your membrane performance. To send a water sample, use two clean containers and fill one with 1/2 cup of tap water and the other with 1/2 cup of RO water.
  • Page 4: Limited Warranty

    Note: some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Other Rights: This Warranty gives you specific legal rights and you may also have other rights which vary from state to state. Pelican Water Systems 877-842-1635, www.pelicanwater.com...
  • Page 5: Performance Data Sheet

    Recovery rating means the percentage of the influent water that is available to the user as reverse osmosis treated water when the system is operated without a storage tank or when the storage tank is bypassed. Model Number: PRO-RO Production Rate: 55.30 L/d (14.61 gpd) Recovery: 26.76%...
  • Page 6: Arsenic Fact Sheet

    The RO component of the PRO-RO system must be replaced yearly to ensure the system will continue to remove pentava- lent arsenic. The component identification and location where you can purchase the component are listed in the installa- tion/operation manual.
  • Page 7 Water Treatment Device Certificate Number 11 - 2076 Date Issued: May 10, 2011 Trademark/Model Designation Replacement Elements Pelican PRO-RO Nimbus Water Maker Five WM5-50 TF50 (4 stage cartridge) 104592 TF50 (4 stage cartridge) 104863 Calcite/GAC (2 stage cartridge GAC postfilter...
  • Page 8: System Specifications

    Iron, normal operating conditions. Hydrogen Sulfide and Manganese. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Pelican Water Systems 877-842-1635, www.pelicanwater.com...
  • Page 9: Faucet Installation

    Be sure to cut the white tubing to the proper length to reach the drain installation (see following Large barb, page). Discard any excess tubing. 3/8” white tubing Small barb, 1/4” black tubing Fig 2: Closeup of faucet barbs Pelican Water Systems 877-842-1635, www.pelicanwater.com...
  • Page 10 Avoid low spots or loops. Cut the tubing shorter, if necessary. 8. Insert the drain tube from the R.O. dispensing faucet through the drain saddle connector nut. Tighten the connector nut onto the drain saddle. Pelican Water Systems 877-842-1635, www.pelicanwater.com...
  • Page 11 4. Fill and flush the tank at least three times prior to use. If necessary, repeat until the chlorination scent has disappeared. It is important that the flush be done at maximum flow (e.g. the tank must be full) to assist in rapid wash out. After this flushing procedure the system is ready for normal use. Pelican Water Systems 877-842-1635, www.pelicanwater.com...
  • Page 12: Installation Checklist

    These parts will not see full pressure until approximately 2 hours after the system is activated. 8. Flush three tankfuls of product water to drain. If a chlorine scent persists, repeat flushing procedure. Pelican Water Systems 877-842-1635, www.pelicanwater.com...
  • Page 13: Maintenance

    9. Open the small shut-off valve on the feed valve assembly. Observe system for any leaks, especially at newly re placed cartridge. 10. Open the tank shut-off valve. 11. The system should be flushed at least once as described in System Activation and Flushing. Pelican Water Systems 877-842-1635, www.pelicanwater.com...

Table of Contents