Download  Print this page

Maintenance; Sewing Light Bulb; To Close Your Elna-tx; To Remedy Minor Disorders - ELNA TX Instruction Manual

Hide thumbs

Advertisement

Table of Contents
Maintenance
To remedy minor disorders
Your Elna-tx will always serve you faithfully if it is
consult the instruction manual on the pages
cared for properly.
indicated, if:
Disconnect the machine according to the "Safety"
The upper thread breaks
Pages
recommendations on page 7.
-
Needle not of the system 130/705 H (15X1),
1 Remove the needle and the foot.
of poor quality, bent, not Inserted correctly,
Slide the rotary hook cover to the rear and
not suitable for the kind of work ........
9-40
remove the bobbin.
-
Incorrectthreading or threead ofpoorquality 16-17
Lift off the needle plate. Remove remains of thread
-
Lower thread not drawn up properly ......
18-19
and fibres by brushing the rotary hook and the
-
Size of thread not suitable for the kind of
feed dog with the cleaning brush.
work .............................
40
2 Place the brush in the middle of the rotary hook
-
Machine needs cleaning ...............
46-47
and move It about so that the bristles protrude
-
Upper tension too tight .............. 19 and 41
through the openings in the side of the hook.
Oil the rotary hook (see pages 12-13).
The lower thread breaks
3 Replace the needle plate. Press down on it so that
-
Thread not wound evenly on the bobbin or
it clicks into place. Put the foot, needle and bobbin
not drawn up correctly (does not cross the
back Into place. Close the rotary hook cover,
bobbin at the right angle) .......... 12-13-14-15
-
Lower tension too tight ...........
19 and 41
Sewing Light Bulb
The machine skips stitches
Maximum input of the lamp 15 w. Remember this,
-
Sewing foot not suitable for the kind of
should it have to be changed.
work ..............................
22-35
The Input of the lamp is also shown on the switch
-
Machine not threaded correctly ......... 16-19
plate of the machine and on the front cover (on the
-
Needle not of the system 130/705 H (15 X 1),
left of the latter).
is the wrong way round, incorrectly inserted,
4 To replace the bulb: first of all, disconnect your
not suitable for the kind of work .........
40
Elna from the mains. Press down on the lug (a).
-
Thread too coarse for the size of needle or
Bayonet socket: push In, turn and remove the bulb.
not flexible enough ..................
40
Replace the bulb by following the same procedure
-
Lower thread not drawn up correctly .....
18-19
In the reverse order. Note its sloping position.
The thread knots beneath the material
To close your Elna-tx
-
The upper tension has not been threaded
-
Remove the upper thread and place a piece of
correctly. Repeat the threading operation., 16-17
cloth under the sewing foot. Lower the thread
The material puckers
guide into the accessory case.
-
Sewing foot not suitable for kind of work
..
22-35
- Turn the flywheel by hand until the thread take-up
-
Thread too thick .....................
40
lever Is in its lowest position. Put the foot control
-
Stitch too long ......................
23
and mains lead into the box provided, which can
-
Upper and/or lower thread tensions too
be kept In your Elna. Push down the spool pin.
tight .............................
41
Close the protection flaps.
-
Lower thread not drawn up correctly ...
18-19

Advertisement

Table of Contents

This manual is also suitable for:

Tx electronic 57

Comments to this Manuals

Symbols: 0
Latest comments:
  • Jeme Prinss Nov 06, 2018 01:41:
    هل يشتغل مكينه بدون دعاسه الرجل