Advertisement

®
OPERATOR'S MANUAL
MODEL #
ORDER #
HDS 5.0/30 Ed / HP-5030D
1.575-650.0
To locate your local Kärcher Shark Commercial Pressure Washer Dealer nearest you,
visit www.karchercommercial.com or www.karchershark.com
9.800-081.0

Advertisement

Table of Contents
loading

Summary of Contents for Kärcher HDS 5.0/30 Ed

  • Page 1 ® OPERATOR’S MANUAL MODEL # ORDER # HDS 5.0/30 Ed / HP-5030D 1.575-650.0 To locate your local Kärcher Shark Commercial Pressure Washer Dealer nearest you, visit www.karchercommercial.com or www.karchershark.com 9.800-081.0...
  • Page 2: Table Of Contents

    The model and serial numbers will be found on a decal attached to the machine. You should record both serial number and date of purchase and keep in a safe place for future reference. Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 3: Introduction

    (GFCI). If rated more than 250 volts, or more than longer than 1-2 minutes. single phase this product should only be con- nected to a power supply receptacle protected by 10. Keep operating area clear of all persons. a GFCI. Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 4: Important Safety Information

    14. Be certain all quick cou- BACK - HOLD WITH under the influence of alcohol, prescription medi- pler fittings are secured be- BOTH HANDS cations, or drugs. fore using pressure washer. Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 5: Installation

    IMPORTANT SAFETY INFORMATION Follow the maintenance instructions specified in the manual. Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 6: Component Identification

    Garden Hose (not included) Insulated Wand (not included) Pressure Washer to Inlet Hose Insulated Spray Gun (not included) Inlet Connection Outlet Connection Power Cord High Pressure Outlet Hose GFCI (not included) Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 7: Installation

    Electrical: This machine, when installed, must be electrically grounded in accordance to local codes. Check for proper power supply using a volt meter. Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 8: Operating Instructions

    STEP 4: For hot water washing, turn the machine burner switch to the ON position. Adjust thermostat to desired temperature setting. (The burner will light automatically.) Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 9: Detergents & General Operating Techniques

    Apply safety latch to spray gun. Remove black soap nozzle from the quick coupler. Select and install the desired high pressure nozzle. NOTE: You can also stop detergent from flowing by simply removing detergent siphon tube from bottle. Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 10: Shutting Down & Cleanup

    This closes both the intake and exhaust valves to prevent rusting of cylinder. Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 11: Troubleshooting

    Obstruction in smoke stack Check for insulation blockage or other foreign objects. Soot build-up on coils Clean coils with soot remover. Lime build-up in coils Clean inside of coils using coil cleaner. Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 12: Preventative Maintenance

    Fittings Check Daily Fuel Filter Clean Weekly Inlet Strainer Clean Weekly Fuel Nozzle Clean Weekly Fuel Tank Clean Weekly Electrodes Adjust Monthly Fuel Pump Strainer Clean Monthly Electrode Wires Check Monthl Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 13: Maintenance And Service

    When soot has been detected on visual observation, By injecting compressed air, all water will be blown out the soot on the coil must be cleaned off. of the system. Run anti-freeze through the system. Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 14: Maintenance And Service

    The solenoid then closes, shutting off the supply of fuel to the combustion chamber. Controlling the flow of fuel Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 15 Thermostat is turned up Flow switch is adjusted properly 12. When machine is operating properly, turn machine off, tighten front panel, and install hood and 13 self tapping screws with recess washers. Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 16: Machine Assembly Exploded View

    EXPLODED VIEW Burner Assembly Details 4, 51, 52, 53 98000810-2 Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 17: Machine Assembly Exploded View Parts List

    Screw, 10/32" x 3/4" 8.932-969.0 Label, Warning, Service Cord 1 9.802-070.0 Grip, 1" Square Handle 9.800-016.0 Label, Disconnect Pwr Supply 1 9.802-107.0 Fastener, Ratchet, Black 9.802-492.0 Block, Terminal, 8 Pole 9.802-494.0 ▲ Bar Jumper Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 18: Burner Assembly Exploded View

    BURNER ASSEMBLY EXPLODED VIEW Inlet Outlet 98000810-1 Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 19: Burner Assembly Exploded View Parts Lists

    6.390-126.0 Hose, 3/8" x 14", 2 Wire, Pressure Loop 9.802-079.0 Tank, Encore, 5 Gallon Fuel 8.933-006.0 Switch, Flow, MV60 9.802-781.0 Nut, 3/8" Whiz Loc 9.802-039.0 Elbow, 1/2" JIC x 3/8", 90° Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 21 Kärcher sales and service representatives are not authorized to waive or alter the terms of this warranty, or to increase the obliga- tions of Kärcher under the warranty. Kärcher reserves the right to make design changes in any of its products without prior notification to the Customer. Karcher • HDS 650 • 9.800-081.0 • Rev. 5/10a...
  • Page 22 ® www.karchercommercial.com www.karchershark.com Form HDS 650 # 9.000-081.0 • Revised 5/10a • Printed in U.S.A. or Mexico...

This manual is also suitable for:

Hp-5030d

Table of Contents