Table of Contents
Advertisement
EN
SECTION 12
AUTODOME LOCKED COMMANDS
Access to the AutoDome may be password-protected. See SECTION 4, AutoDome Security for details. To use Locked Commands, first unlock
the AutoDome via OFF-90-ENTER. All locked settings, except FastAddress, can then be changed via ON-46-ENTER. Disallow these commands via
ON-90-ENTER.
Commands
Keystrokes
FastAddress
On-999-Enter
On-998-Enter
Display FastAddress On-997-Enter
Auto Iris
On/Off-3-Enter
Auto Focus
On/Off-4-Enter
Gain Control
On/Off-43-Enter
On-screen Display On/Off-60-Enter
On-screen
On/Off-61-Enter
Display Adjust
Sector Title Edit
On/Off-63-Enter
Sector Blanking
On-86-Enter
Privacy Masking
On-87-Enter
Bypass All
Off-86-Enter
Masks/Blanking
or Off-87-Enter
Lock/Unlock
On/Off-90-Enter
Commands
Password
Set-802-Enter
Factory Home
Set-110-Enter
Position
Restore Defaults
On-40-Enter
Left Limit
Set-101-Enter
Right Limit
Set-102-Enter
Inactivity
On/Off-9-Enter
Preset
On/Off-15-Enter
Tour Period
AutoPivot
On/Off-18-Enter
AutoTrack Comms
On/Off-77-Enter
Camera Height
On/Off-79-Enter
Select
On/Off-35-Enter
White Balance
or On/Off-30-Enter
Sharpness
On/Off-44-Enter
Iris Adjust
On/Off-11-Enter
Shutter
On/Off-23-Enter
(Frame Integration)
Sync Mode
On/Off-42-Enter
Adjust Line
On/Off-41-Enter
Lock Phase
Switch Polarity
On-91-Enter
Digital Zoom
On/Off-80-Enter
Night Threshold Adj. On-58-Enter
QuickSet Select
On-59-Enter
QuickSet Mode Name
Gain Control
Low Light Color
Auto
Full Auto w/ Slow Shutter
Auto
Full Auto w/o Slow Shutter
Auto
Night w/ Slow Shutter
Auto
Night w/o Slow Shutter
Auto
© 2005 Bosch Security Systems
Description
Sets/changes the dome address using the keyboard and on-screen menus. (for cameras not already configured).
Sets/changes the dome address using the keyboard and on-screen menus. (for all cameras, even those already configured).
Briefly displays all dome addresses.
Camera (Iris) adjusts automatically/manually (On/Off) to light conditions.
Camera automatically/manually (On/Off) focuses.
Turns gain control to Automatic or Off. When in Automatic mode, the gain increases to compensate for darker scenes.
Turns On/Off the On-screen Display. When off, there is no On-screen feedback.
Changes the characters and position of the display.
On-screen instructions are provided.
Newer versions of the Receiver/Driver, in combination with firmware version 5.10 or higher, allow the brightness to be
adjusted. The firmware automatically detects whether the Receiver/Driver supports this, and displays the selection when
available.
Edits the current Sector name. On-screen instructions are provided.
Masks video from being displayed in selected sectors.
Masks video from being displayed in selected zones.
Removes all viewing restrictions imposed by sector blanking/privacy masking but keeps their locations in memory.
On-86/87-Enter reactivates all masks/blanking.
Allows/Disallows Locked Commands to be accessed.
Sets or displays password. See AutoDome Security, SECTION 4 for details.
SET recalibrates camera and returns it to home position.
Restores Factory Defaults.
Sets the current position as the left limit of Auto Pan. Default is 0 degrees.
Sets the current position as the right limit of Auto Pan. Default is 359.9 degrees.
Selects the mode that the dome reverts to after a duration without operator activity. Default is OFF.
Increase/Decrease (On/Off) the time between Presets during Preset Tour.
Allows a subject to be followed while beneath the camera, without inverting the picture. Default is ON.
Enables/Disables the Tracker. When disabled, no status will be displayed. Since this is not retained in non-volatile memory, if
the AutoDome receives Tracker messages on start-up, the Tracker will be enabled again (AutoTracker option ONLY).
Selects the height of the camera in respect to the surface being monitored with the AutoTracker feature
(AutoTracker option ONLY).
Adjusts camera color (white balance) for specific settings.
Picture (vertical aperture) sharpens/softens.
Edits the Auto Iris level.
Sliding scale from 1 second to 1/10,000 sec,
with Auto Slow Shutter at extreme left.
Sets camera sync for external-line/internal-crystal (On/Off).
Changes the phase delay of the camera when in
external line lock mode.
Switches the polarity of the Zoom, Focus, and Iris controls.
Enables (On) or disables (Off) the digital zoom.
Selects the video level at which the camera switches to night mode (Day/Night only).
Allows mode selection where multiple camera settings are set according to the chart below (Day/Night only).
IRIS
Slow Shutter
IR Filter
Auto
Auto
In
Auto
Auto
Auto
Auto
1/60
Auto
Auto
Auto
Out
Auto
1/60
Out
Section 12
Page 26 of 40
Hide quick links:
Advertisement
Table of Contents
