Philips 55PFT6609 User Manual page 29

successfully. Unplug the USB memory device.
To an already installed TV
1 - Verify the country setting of the TV. (To verify this setting,
press  and select Setup and press OK. Select Search for
channels > Re-install channels and press OK. Press  and
later Cancel to leave the Search for channels.)
If the country is correct continue with step 2.
If the country is not correct, you need to start a reinstallation. To
start the reinstallation, press  and select Setup and press OK.
Select TV settings > General settings > Reinstall TV > OK.
Select the correct country and skip the Search for channels.
Finish the installation. When done, continue with step 2.
2 - Plug in the USB memory device that holds the channel list of
the other TV.
3 - To start the channel list upload, press  and
select Setup and press OK.
4 - Select TV settings > General settings > Channel list copy >
Copy to TV and press OK. You might be asked to enter the
Child lock code of this TV.
5 - The TV notifies you if the channel list is copied to the TV
successfully. Unplug the USB memory device.
DVB-T or DVB-C
DVB-T or DVB-C reception
If both DVB-T and DVB-C reception is available in your country
and if this TV is ready to receive DVB-T and DVB-C for your
country, you have selected one or the other during the channel
installation.
If you want to change the DVB setting to start a new channel
installation . . .
1 - Press  and select Setup and press OK.
2 - Select Channel settings and press OK.
3 - Select Channel installation > Antenna connection >
Antenna (DVB-T) or Cable (DVB-C) and press OK.
4 - Select the DVB setting you want.
5 - Press , repeatedly if necessary, to close the menu.
DVB-C channel installation
For ease of use, all DVB-C settings are set to automatic.
If your DVB-C provider gave you specific DVB-C values, the
network ID or network frequency, enter these values when the
TV asks for them during installation.
It might be necessary to adjust the scanning (full or quick scan)
or enter a specific symbol rate in the Settings menu while
installing. To set a Symbol rate, first set the Symbol rate to
Manual.
Channel number conflicts
In some countries, different TV channels (broadcasters) might
have the same channel number. While installing, the TV shows
the list with channel number conflicts. You need to select which
TV channel you want to install on a channel number with
multiple TV channels.
DVB-T + DVB-C
If you can use a DVB-T antenna input but also a DVB-C input,
you can set up your TV for both DVB-T and DVB-C. Install one
system followed by the other with the necessary settings.
Once each system is installed, you need to switch the antenna
input signal on the Antenna connection on the back of the TV
and set the TV in the appropriate system to view the installed
channels on TV.
To select the DVB-T or DVB-C setting, see above.
DVB settings
Access DVB settings
1 - Press  and select Setup and press OK.
2 - Select Search for channels and press OK.
3 - Select Re-install Channels.
4 - Select the country where you install this TV.
5 - Select Cable (DVB-C).
6 - Select Start to search channels, or select Settings for DVB-
C settings.
7 - Press  , repeatedly if necessary, to close the menu.
Symbol rate mode
If your cable provider did not give you a specific symbol rate
value to install the TV channels, leave the Symbol rate mode
setting on Automatic.
If you received a specific symbol rate value, select Manual.
However, the value you received could be in the predefined list
of symbol rates already. Select Predefined symbol rates to
check if your value is available automatically.
Predefined symbol rates
With the Symbol rate mode set to Automatic, the TV will use 1
of the predefined symbol rates as used by most cable providers
in your country.
Symbol rate
With the Symbol rate mode set to Manual, you can enter the
symbol rate value you received from your cable provider. To
enter the value, use the number keys.
Symbol rate 2
With the Symbol rate mode set to Manual, you can enter a
second symbol rate value you received from your cable
provider. To enter the value, use the number keys.
29