Focus Lens Adjustment; Focus Vr Adjustment - Sony KP-46WT520 Service Manual
Sony color rear video projection
Hide thumbs
Also See for KP-46WT520:
- Service manual (157 pages) ,
- Operating instructions manual (85 pages) ,
- Specifications (2 pages)
Table of Contents
Advertisement
2-4. FOCUS LENS ADJUSTMENT
In this adjustment, use the remote commander while in service mode.
For details on the usage of the service mode and the remote commander,
please refer to section
2-10. ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER.
1. Loosen the lens screw.
2. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off the
CRTs individually without using lens caps).
3. Turn the green lens to adjust to the optimum focus point with the
crosshatch signal.
4. Tighten the lens screw.
5. Cover the green and blue CRT lenses with the lens caps to allow only
red to show (or use the method shown in the note below for turning off
the CRTs individually without using lens caps).
6. Turn the red lens to adjust to the optimum focus point with the
crosshatch signal.
7. Tighten the lens screw.
8. Cover the green and red CRT lenses with the lens caps to allow only
blue to show (or use the method shown in the note below for turning
off the CRTs individually without using lens caps).
9. Turn the blue lens to adjust to the optimum focus point with the
crosshatch signal.
10. Tighten the lens screw.
11. After adjusting the items:
2-5. FOCUS VR ADJUSTMENT,
2-7. 2-POLE MAGNET ADJUSTMENT,
2-8. 4-POLE MAGNET ADJUSTMENT,
reconfi rm the optimum focus point and adjust again if necessary.
* In PJE mode, every time 6 is pressed, the test signal changes to:
“crosshatch+video signal” → “crosshatch+borderline (black)” →
”crosshatch (black)” → “dots (black)” → “all white” → off
Test Signal
Scanning line visible.
A
Minimize both A and B.
B
Lens
Center of crosshatch
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams by controlling the service mode MCP-RON, GON, BON.
KP-46WT520/51WS520/57WS520
KP-46WT520/51WS520/57WS520
2-5. FOCUS VR ADJUSTMENT
1. Set generator to crosshatch.
2. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off the
CRTs individually without using lens caps).
3. Turn the green focus VR on the focus block to adjust to the optimum
focus point with the crosshatch signal.
4. Cover the green and blue picture lenses with lens caps to allow only
red to show (or use the method shown in the note below for turning off
the CRTs individually without using lens caps).
5. Turn the red focus VR on the focus block to adjust to the optimum
focus point with the crosshatch signal.
6. Cover the green and red picture lenses with lens caps to allow only
blue to show (or use the method shown in the note below for turning
off the CRTs individually without using lens caps).
7. Turn the blue focus VR on the focus block to adjust to the optimum
focus point with the crosshatch signal.
8. After adjusting the items:
2-4. FOCUS LENS ADJUSTMENT,
2-7. 2-POLE MAGNET ADJUSTMENT,
2-8. 4-POLE MAGNET ADJUSTMENT,
reconfi rm the optimum focus point and adjust again if necessary.
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams by controlling the service mode MCP-RON, GON, BON.
R
G
B
SCREEN
R
G
B
FOCUS
FOCUS Block
Page 32
- Quick Links:
- Self-Diagnostic Function
Hide quick links:
Advertisement
Table of Contents
