NAD C 355BEE Owner's Manual
Integrated amplifier
Hide thumbs
Also See for C 355BEE:
- Owner's manual (99 pages) ,
- Service manual (37 pages) ,
- Specifications (2 pages)
Related Manuals for NAD C 355BEE
Summary of Contents for NAD C 355BEE
-
Page 1: Integrated Amplifier
C 355BEE ® Integrated Amplifier Owner’s Manual Manuel d’Installation Manual del Usuario Manuale delle Istruzioni Bedienungsanleitung Gebruikershandleiding Bruksanvisning Инструкция по эксплуатации... -
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS 1. Read instructions - All the safety and operating instructions should NOTE TO CATV SYSTEM INSTALLER be read before the product is operated. This reminder is provided to call the CATV system installer’ s attention to Section 820-40 2. - Page 3 RECORD YOUR MODEL NUMBER (NOW, WHILE YOU CAN SEE IT) To maintain proper ventilation, be sure to leave a space around the unit The model and serial number of your new C 355BEE are located on the (from the largest outer dimensions including projections) than is equal to, back of the cabinet.
-
Page 4: Getting Started
5 Press the required input selector. disconnect the plug from the AC socket. Should water get into your NAD C 355BEE, shut off the power to the unit and remove the plug from the AC socket. Have the unit inspected by a qualified service technician before attempting to use it again. -
Page 5: Identification Of Controls
5 TONE DEFEAT: The TONE DEFEAT switch bypasses the tone control 2 POWER/STANDBY/PROTECTION LED: Upon switching the power section of the NAD C 355BEE. If the Tone Controls are not normally ON, the LED will light up red for a few seconds before the protection used and left in the 12 o’clock position, then it is advisable to switch... - Page 6 NAD type, designed to operate several NAD models. Some buttons on this handset are inoperative as the functions aren’t supported by the C 355BEE. The Video 2 and Video 3 input selector buttons on the remote control handset are inoperative in the case of the C 355BEE.
-
Page 7: Rear Panel
11 12 13 ATTENTION! Please make sure that the C 355BEE is powered OFF or unplugged before making any connections. It is also advisable to power-down or unplug all associated components while making or breaking any signal or AC power connections. - Page 8 ‘L+’ and ‘L-’ to the left speaker in the same way. C 355BEE. Put the source tape in the recorder connected to Tape 2 and the blank tape into the recorder connected to Tape Monitor. By selecting TAPE Always use heavy duty (16 gauge;...
- Page 9 IDENTIFICATION OF CONTROLS SR 6 REMOTE CONTROL Press in and lift tab to remove battery cover out Place batteries into opening. Ensure the correct Replace battery cover by aligning and inserting of recess. fitting is observed. the two tabs into the holes. Press battery cover into place until ‘clicks’...
- Page 10 BLEND: The Blend button toggles between engaging and disengaging replacing batteries, check that they have been put in the right way round, the Blend feature. The NAD Blend feature will allow you to reduce the as indicated on the base of the battery compartment.
-
Page 11: Troubleshooting
REFERENCE TROUBLESHOOTING CONDITION POSSIBLE CAUSES POSSIBLE SOLUTIONS No sound. • Power AC lead unplugged or power not • Check if AC lead is plugged in and power switched ON. switched ON. • Tape Monitor selected. • De-select Tape Monitor mode. •... -
Page 12: Preamplifier Section
5 CCIF IM distortion, 19.5K+1kHz rated output 6 Gross dimensions include feet, volume knob and extended speaker terminals. Specifications are subject to change without notice. For updated documentation and features, please log onto www.NADelectronics.com for the latest information about C 355BEE. - Page 14 ©2008 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International C 355BEE Manual Issue 2-04/08...