Summary of Contents for Husqvarna K 3000 Cut-n-Break
Page 1
Oper ator ′ s manual K 3000 Cut-n-Br eak Please r ead the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
KEY T O SYMBOLS Symbols on the mac hine: En vironmental marking. Symbols on the product or its packaging indicate that W ARNING! The machine can be a this product cannot be handled as dangerous tool if used incorrectly or domestic waste.
CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ........2 Symbols in the operator’s manual: ....... 2 CONTENTS Contents ............... 3 WHA T IS WHAT? What is what on the po wer cutter? ....... 4 GENERAL SAFETY PRECA UTIONS Steps bef ore using a new power cutter ....
WHA T IS WHA T? What is what on the po wer cutter? Front handle 11 Brush retainer Rear handle 12 Belt tensioner Switch 13 Water tap Power switch lock 14 Cutting arm Blades 15 Ground fault circuit interrupter (not for GB) Rating plate 16 Water connector Splash guard...
SAFETY INSTR UCTIONS General saf ety warnings • When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of cord suitable for outdoor use reduces the risk of electric W ARNING! Read all safety warnings and shock.
SAFETY INSTR UCTIONS • If devices are provided for the connection of dust danger. Make sure that sparks are not caused when extraction and collection facilities, ensure that these cutting in view of the risk of explosion. Remain are connected and properly used. Use of dust concentrated and focused on the task.
SAFETY INSTRUCTIONS Power switch lock Blade guards The power switch lock is designed to prevent accidental This guard is fitted above and below the cutting blade and operation of the switch. When the lock (A) is pressed in is designed to prevent parts of the blade or cutting the power switch (B) is released.
SAFETY INSTRUCTIONS High speed handheld machines • Always use a sharp diamond blade. • Ensure the blades are not cracked or damaged in any • Only use special blades with integrated belt pulley other way. Replace blades if necessary. halves on this machine. •...
Page 10
SAFETY INSTRUCTIONS • Check that the blade is not in contact with anything • Repeat this working method until the required cutting when the machine is started depth is achieved (D, E). • Start cutting with the machine running at maximum speed.
Page 11
SAFETY INSTRUCTIONS Kickback • Keep a good balance and a firm foothold. • When cutting vertically, always cut from the top of the Kickback is a sudden, rearward motion of the saw that can cut and down. occur if the blades are stalled (pinched, jammed, twisted) in the so called kickback zone.
Assembling the blades • Husqvarna blades are especially manufactured and approved for freehand cutting with the K3000 Cut-n- Break. The blades have integrated belt pulley halves and are to be changed in pairs.
STARTING AND STOPPING Before starting Stopping • Stop the motor by releasing the power switch. WARNING! Note the following before starting: The machine should be connected to an earthed outlet socket. WARNING! The cutting blade continues Check that the mains voltage to rotate for some time after the motor corresponds with that stated on the has stopped.
MAINTENANCE General Check the tension of the drive belt • Stick a screwdriver in the notch. • A correctly adjusted drive belt should have about 5 mm of movement. WARNING! Inspection and/or maintenance should be carried out with the motor switched off and the plug disconnected.
MAINTENANCE Replacing the drive belt • Remove the cutting arm by pulling it straight out from the machine. • Release the belt tension. • Remove the blades. • Loosen the five screws holding the guards on the cutting arm. • Remove the belt cover by loosening the nuts, the clamping bolt and the eccentric cam.
MAINTENANCE Cooling system Water tap • Check and clean the restrictor if necessary. Do not use hoses that are distorted, worn or damaged. Electrical Feed • The machine is equipped with an efficient fan to cool the motor. Cooling air which is drawn in through the WARNING! Never use damaged cables.
TECHNICAL DATA Technical data K 3000 Cut-n-Break Engine Protection class Max. blade speed, rpm 4700 Rated voltage, V Europe Great Britain USA / Canada / Japan 100-120 Rated output, W Europe 2700/12 A Great Britain 2200/20 A USA / Canada / Japan...
Husqvarna AB, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter Husqvarna Cut-n-Break dating from 2010 serial numbers and onwards (the year is clearly stated on the rating plate, followed by the serial number), complies with the requirements of the COUNCILíS DIRECTIVE: •...
Page 20
1153344-26 Original instructions ´®z+UBJ¶6l¨ ´®z+UBJ¶6l¨ 2009-12-29...