Related Manuals for Axis Q6032-C
Summary of Contents for Axis Q6032-C
- Page 1 INSTALLATION GUIDE AXIS Q60 Series AXIS Q6032-C PTZ Dome Network Camera AXIS Q6034-C PTZ Dome Network Camera AXIS Q6035-C PTZ Dome Network Camera...
- Page 2 Internet, you can: • download user documentation and firmware updates • find answers to resolved problems in the FAQ database. Japan - Search by product, category, or phrases • report problems to Axis support by logging in to your private support area...
-
Page 3: Battery Replacement
Battery Replacement This Axis product uses a 3.0 V BR2032 lithium battery as the power supply for its internal real-time clock (RTC). Under normal conditions this battery will last for a minimum of 5 years. Low battery power affects the operation of the RTC, causing it to reset at every power-up. -
Page 4: Cleaning Of Dome Cover
Cleaning of Dome Cover • Be careful not to scratch or damage the dome cover. Do not clean a dome cover that looks clean to the eye and never polish the surface. Excessive cleaning could damage the surface. • For general cleaning of a dome cover it is recommended to use a non-abrasive, solvent-free neutral soap or detergent with water and a soft cloth. -
Page 5: Installation Steps
Page 5 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide This Installation Guide provides instructions for installing AXIS Q6032-C/Q6034-C/Q6035-C PTZ Dome Network Camera on your network. For all other aspects of using the product, please see the User Manual, available at www.axis.com Installation Steps 1. -
Page 6: Hardware Overview
Page 6 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Hardware Overview Sunshield Screw hole (3x) Hole for unit holder (3x) Part number (P/N) & Serial number (S/N). The serial number may be required during the installation. Multi-connector Alignment indicator Hook for safety wire... - Page 7 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 7 Camera unit Cooling system (See page 22 for cleaning instructions.) SD card slot Power button (for Factory Default only) Control button Status LED indicator Metal ring screw (4x) Dome cover Dome ring Metal ring...
- Page 8 Page 8 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Media converter switch Ground screw Multi-connector cable Power connector (DC input) I/O connector (external) Power connector (DC output) Network connector (internal) I/O connector (internal) Power LED indicator Network connector SFP (external) (2x) Network LED indicator (4x)
-
Page 9: Media Converter Switch
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 9 Connectors Camera SD card slot - A standard or high capacity SD card (not included) can be used for local recording with removable storage. Install an SD Card (not To insert and remove the SD card, the dome cover must be removed, see included), on page 14. - Page 10 Page 10 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Network connector SFP (external) - Two SFP connectors (100Base-FX/1000Base-X) for network connectivity. Each RJ-45 and SFP connector has its own dip switch. The dip switches control how the port forwards data. See the User Manual for more information.
- Page 11 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 11 I/O connector (internal) - 2-pin I/O terminal block.
-
Page 12: Multi-Connector Cable
Page 12 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Multi-Connector Cable The supplied multi-connector cable is required in order to maintain the camera’s IP rating. Connect the multi-connector cable to the camera’s multi-connector and to the connectors in the supplied media converter switch, see illustrations on page page 6 and page 8. -
Page 13: Electrical Specifications
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 13 Electrical Specifications Unit Function Description Network camera Input Power 65 W (min) Media converter switch Input Voltage 12.0 - 13.2 V DC Input Current 6.25 A (min) Input Power 75 W (min) Available Output Power... -
Page 14: Install The Hardware
Remove the protective packaging between the camera and the sunshield before installing the camera. • A smoked dome cover can be purchased from your Axis reseller. Follow the instructions Replace the Clear/Smoked Dome Cover (optional accessory) to replace the dome cover. - Page 15 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 15 8. Put the dome ring with the dome cover back in the original position and tighten the screws (torque 4 Nm). Make sure to align the bulge on the dome cover with the cooling system on the camera unit.
-
Page 16: Install The Power Supply And The Media Converter Switch
• Axis can only guarantee full functionality with the supplied media converter switch, no other devices are supported. 1. Make sure the mains supply is switched off. 2. Mount the power supply and the media converter switch on the wall or, if applicable, attach them to a DIN rail in the cabinet. - Page 17 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 17 4. Strip the multi-connector cable. Make sure all three shields are intact. 7–8 mm (0.28”–0.32”) Power Blue Digital I/O Green/white Ethernet Green Ethernet Orange/white Ethernet Orange Ethernet Yellow Digital I/O Black Ground Shield Shield (2x) Power 5.
- Page 18 Page 18 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Power connector (DC output) Clamp Shield Ethernet connector Shield (2x) (internal) I/O connector (internal) Ethernet connector (internal) 7. Make sure the clamp is in place and tighten the screws. • The shield and the clamp surface shall be in full contact with each other so that the multi- connector cable is grounded.
- Page 19 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 19 8. Connect the network cables to the external network connectors (RJ-45, SFP) as required. Ground screw Power cable (DC input) Multi-connector cable Power connector (DC input) I/O connector (external) Network connector SFP (external) (2x)
- Page 20 Page 20 AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide 12. If connecting several media converter switches in a daisy chain, set the dip switch of each outgoing network connector port that connects to another media converter switch to position C. Leave the dip switch in its default position (position B) when connecting the port...
-
Page 21: Install The Network Camera
1. Install the selected bracket (sold separately) according to the instructions supplied with the bracket. If drilling is required, make sure to use drill bits, screws, and plugs that are appropriate for the material. See www.axis.com for information on available mounting accessories. 2. Route the multi-connector cable through the bracket. -
Page 22: Access The Axis Product
The Live View Page The product’s Live View page appears in your browser. Click Setup to open the product’s Setup pages, which allow you to customize the Axis product. Setup - Provides all the tools for con- Help - Displays online help on all figuring the product to requirements. -
Page 23: Cleaning Of Outer Heat Sink
AXIS Q6032-C/Q6034-C/Q6035-C Installation Guide Page 23 Cleaning of Outer Heat Sink Dust and particle buildup could affect the performance of the cooling system. To maintain the performance level, the outer heat sink in the camera’s cooling system may need occasional or regular cleaning. -
Page 24: Resetting To The Factory Default Settings
Management Software CD. It is also possible to reset parameters to the original factory default settings via the web interface. For more information, see the online help or the User Manual available at www.axis.com Further Information The User Manual is available from the Axis Web site at www.axis.com Tip! Visit www.axis.com/techsup to check if there is updated firmware available for your network... - Page 26 Ver.1.3 Installation Guide AXIS Q6032-C/Q6034-C/Q6035-C Printed: October 2012 Part No. 48913 © Axis Communications AB, 2012...