Makita BBC231U Instruction Manual page 4

4. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
5. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, seek medical help. Liquid ejected
from the battery may cause irritation or burns.
6. Do not dispose of the battery(ies) in a fire. The cell
may explode. Check with local codes for possible
special disposal instructions.
7. Do not open or mutilate the battery(ies). Released
electrolyte is corrosive and may cause damage to
the eyes or skin. It may be toxic if swallowed.
Starting up the tool
360°
010822
1. Make sure that there are no children or other
people within a working range of 15 meters (50 ft),
also pay attention to any animals in the working
vicinity. Otherwise stop using the tool.
2. Before use always check that the tool is safe for
operation. Check the security of the cutting tool
and the guard and the switch trigger/lever for easy
and proper action. Check for clean and dry
handles and test the on/off function of the switch.
3. Check damaged parts before further use of the tool.
A guard or other part that is damaged should be
carefully checked to determine that it will operate
properly and perform its intended function. Check
for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
condition that may affect its operation. A guard or
other part that is damaged should be properly
repaired or replaced by our authorized service
center unless indicated elsewhere in this manual.
4. Switch on the motor only when hands and feet are
away from the cutting tool.
5. Before starting make sure that the cutting tool has
no contact with hard objects such as branches,
stones etc. as the cutting tool will revolve when
starting.
Method of operation
1. Only use the tool in good light and visibility. During
the winter season beware of slippery or wet areas,
ice and snow (risk of slipping). Always ensure a
safe footing.
2. Take care against injury to feet and hands from the
cutting tool.
3. Never cut above waist height.
4. Never stand on a ladder and run the tool.
5. Never climb up into trees to perform cutting
operation with the tool.
6. Never work on unstable surfaces.
7. Remove sand, stones, nails etc. found within the
working range. Foreign particles may damage the
cutting tool and can cause dangerous kick-backs.
8. Should the cutting tool hit stones or other hard
objects, immediately switch off the motor and
inspect the cutting tool.
9. Inspect the cutting blade at short regular intervals
for damage (detection of hairline cracks by means
of tapping-noise test).
10. Before commencing cutting, the cutting tool must
have reached full working speed.
11. Operate the tool only with the shoulder harness
attached which is to be suitably adjusted before
putting the tool into operation. It is essential to
adjust the shoulder harness according to the user
size to prevent fatigue occurring during use.
12. During operation always hold the tool with both
hands. Never hold the tool with one hand during
use. Always ensure a safe footing.
13. The cutting tool has to be equipped with the guard.
Never run the tool with damaged guards or without
guards in place!
14. All protective equipment such as guards and the
shoulder harness supplied with the tool must be
used during operation.
15. Never hit weeds or similar materials with the
cutting tool to cut them away.
16. Except in case of emergency, never drop or cast
the tool to the ground or this may severely damage
the tool.
17. Never drag the tool on the ground when moving
from place to place, the tool may become
damaged if moved in this manner.
18. Always remove the battery cartridge from the tool:
− whenever leaving the tool unattended;
− before clearing a blockage;
− before checking, cleaning or working on the
tool;
− whenever the tool starts vibrating abnormally.
19. Always ensure that the ventilation openings are
kept clear of debris.
4