F7.5: Control Change On/Off; F7.6: Midi Transmit Transpose; F7.7: Panel/Status Transmit; F7.8: Bulk Data Dump - Yamaha YPP-200 Ligh Piano Owner's Manual

The Function Mode

F7.5: Control Change ON/OFF

MIDI device or keyboard, causing the voice on the corresponding channel to be affected by
pedal and other "control" settings received from the controlling device (the keyboard voice is
not affected). The YPP-200 also transmits MIDI control change information when one of its
pedals or other appropriate controls are operated.
that, for example, the YPP-200 pedals and other controls can be operated without affecting an
external MIDI device.
"On" or "OFF".

F7.6: MIDI Transmit Transpose

down in semitone increments by up to plus or minus 12 semitones. The pitch of the YPP-200
itself is not affected.
tion. The range is from "–12" (down one octave) through "0" (no transposition) to "12" (up
one octave).

F7.7: Panel/Status Transmit

transmitted via the MIDI OUT terminal. This is particularly useful if you will be recording
performances to a MIDI sequence recorder such as the Yamaha MIDI Data Filer MDF3 which
will be used to control the YPP-200 on playback. By transmitting the YPP-200 panel settings
and recording them on the MIDI sequence recorder prior to the actual performance data, the
YPP-200 will be automatically restored to the same settings when the performance is played
back.
display when the data has been successfully transmitted.

F7.8: Bulk Data Dump

storage device such as the Yamaha MIDI Data Filer MDF3, other sequence recorders, or MIDI
compatible computers.
display when the data has been successfully transmitted.
32
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
YPP-200
Normally the YPP-200 will respond to MIDI control change data received from an external
This function makes it possible to cancel control change data reception and transmission so
Use the [–/NO] and [+/YES] buttons to turn control change transmission and reception
Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting "On".
• For information on control changes that can be used with the YPP-200, refer to the MIDI Data Format
on page 41.
This function allows the MIDI note data transmitted by the YPP-200 to be transposed up or
Use the [–/NO] and [+/YES] buttons to set the desired amount of MIDI transmit transposi-
Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting "0".
This function causes all the current YPP-200 panel settings (selected voice, etc.) to be
Press the [+/YES] button to transmit the panel/status data. "End" will appear on the LED
• See page 42 for list of the "Panel Data Contents" transmitted by this function.
• Panel setting data that is transmitted to an external device can only be reloaded on a model of the
same type. Panel setting data can also be directly transferred to or from instruments of the same
model type.
This function is used to transmit all data stored in the Recorder memory to a MIDI data
Press the [+/YES] button to begin bulk transmission. "End" will appear on the LED
• User song recorder data that is transmitted to an external device can only be reloaded on a model of
the same type. Recorder data can also be directly transferred to or from instruments of the same
model type.
• The reload operation cannot be executed when the demo/preset song mode or user song recorder is
in operation, or when the Function mode is engaged.
• No MIDI note/panel data transmission or data reception occurs during a bulk data dump transmit operation.
......................................................................................................
....................................................................................................
............................................................................................................
............................................................................................................................