Maintenance - Makita 5360-21 Operator's Manual

Rotary hammers
Hide thumbs

Advertisement

Table of Contents
To reduce the risk of injury, always unplug
your tool before performing any maintenance.
Never disassemble the tool or try to do any
rewiring on the tool's electrical system. Contact
a MILWAUKEE service facility for ALL repairs.
Maintaining Tools
Keep your tool in good repair by adopting a regular maintenance pro-
gram. Before use, examine the general condition of your tool. Inspect
guards, switches, tool cord set and extension cord for damage. Check
for loose screws, misalignment, binding of moving parts, improper mount-
ing, broken parts and any other condition that may affect its safe opera-
tion. If abnormal noise or vibration occurs, turn the tool off immediately
and have the problem corrected before further use. Do not use a dam-
aged tool. Tag damaged tools "DO NOT USE" until repaired
(see "Repairs").
Under normal conditions, relubrication is not necessary until the motor
brushes need to be replaced. After six months to one year, depending on
use, return your tool to the nearest MILWAUKEE service facility for the
following:
Lubrication
Brush inspection and replacement
Mechanical inspection and cleaning (gears, spindles, bearings,
housing, etc.)
Electrical inspection (switch, cord, armature, etc.)
Testing to assure proper mechanical and electrical operation
To reduce the risk of injury, electric shock and
damage to the tool, never immerse your tool in
liquid or allow a liquid to flow inside the tool.
To reduce the risk of injury, always unplug the
tool before attaching or removing accessories.
Use only specifically recommended accesso-
ries. Others may be hazardous.
For a complete listing of accessories refer to your MILWAUKEE Electric
Tool catalog or go on-line to www.milwaukeetool.com. To obtain a
catalog, contact your local distributor or a service center.
Carrying Case
Cat. No. 48-55-5359
Same as provided with the tool.
Quick Change Chuck Adapter (5360-21 only)
Cat. No. 48-03-3047
For use with 1/2" Chuck Cat. No. 48-66-1360.
WARNING!
WARNING!
WARNING!

MAINTENANCE

Cleaning
Clean dust and debris from vents. Keep the tool handles clean, dry and
free of oil or grease. Use only mild soap and a damp cloth to clean your
tool since certain cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include: gasoline, turpentine,
lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia
and household detergents containing ammonia. Never use flammable or
combustible solvents around tools.
Repairs
If your tool is damaged, return the entire tool to the nearest service
center.
FIVE YEAR TOOL LIMITED WARRANTY
Every MILWAUKEE tool is tested before leaving the factory and is war-
ranted to be free from defects in material and workmanship. MILWAUKEE
will repair or replace (at MILWAUKEE's discretion), without charge, any
tool (including battery chargers) which examination proves to be defec-
tive in material or workmanship from five (5) years after the date of
purchase. Return the tool and a copy of the purchase receipt or other
proof of purchase to a MILWAUKEE Factory Service/Sales Support
Branch location or MILWAUKEE Authorized Service Station, freight pre-
paid and insured. This warranty does not cover damage from repairs
made or attempted by other than MILWAUKEE authorized personnel,
abuse, normal wear and tear, lack of maintenance, or accidents.
Battery Packs, Flashlights, and Radios are warranted for one (1) year
from the date of purchase.
THE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN ARE
EXCLUSIVE. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY
INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, INCLUDING
LOSS OF PROFITS.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRAN-
TIES, OR CONDITIONS, WRITTEN OR ORAL, EXPRESSED OR IMPLIED FOR
MERCHANTABLILITY OR FITNESS FOR PARTICULAR USE OR PURPOSE.
This warranty gives you specific legal rights. You may also have other
rights that vary from state to state and province to province. In those
states that do not allow the exclusion of implied warranties or limitation
of incidental or consequential damages, the above limitations or exclu-
sions may not apply to you. This warranty applies to the United States,
Canada, and Mexico only.
ACCESSORIES
Chuck Adapter (5359-21 or 5360-21)
Cat. No. 48-03-3005
Converts SDS drive to 1/2" - 20 thread. For use with 1/2" Chuck Cat. No.
48-66-1360.
Removable SDS Bit Holder
Cat. No. 48-66-3042
1/2" Chuck
Cat. No. 48-66-1360
For use with Chuck Adapters Cat. No. 48-03-3005 and 48-03-3047. Not
recommended for hammering applications. Use with drilling action only.
Key included.
SDS Shank Bits, SDS Shank Chisels, and SDS Shank Core Bits
and Adapters are also available. Refer to your MILWAUKEE Electric
Tool catalog.
page 7

Advertisement

Table of Contents
loading

  Related Manuals for Makita 5360-21

This manual is also suitable for:

5359-21