Plug & Play (Initial Setup) - Samsung 6300 User Manual

When you turn the TV on for the first time, a sequence of on-screen prompts will assist in configuring basic settings. To turn on
the TV, press the POWERP button.
✎
Plug & Play is available only when the Source is set to TV.
✎
To return to the previous step in the Plug & Play sequence, select Previous, and then press ENTERE.
✎
Before turning on the TV, make you have connected the TV to an antenna or cable connection (p. 8).
1
Selecting the OSD
Language
2
Setting up the Network
3
Software Upgrade
4
Selecting the usage
mode
5
Setting the Clock
Mode
6
Selecting search
options for auto tuning
7
Selecting and
memorizing channels
8
Enjoy your TV.
If You Want to Rerun Plug & Play...
O
MENU → System → Plug & Play → ENTERE
✎
NOTE
x
To change the TV's setting from Store Demo to Home Use when not in Plug & Play, press the volume button on the
TV. When you see the volume bar on the screen, press and hold the
[UD6300-ZA]BN68-03534A-03Eng.indb 9
Plug & Play (Initial Setup)
Press the ▲ or ▼ button to select a language. Press ENTERE twice
when done.
Set up your network connection. Press the ENTERE button to start. If
you do not know your network set up information or want to set to it later,
select Skip. We suggest you skip network connection setup now and
refer to "Wired/Wireless Network Connection" in the e-Manual for set up
requirements and instructions, and the Network Connection section of this
manual (Page 15). You can set up the network connection later using the
Network menu.
When network connection settings are complete, Software Upgrade is available. Select
Next to upgrade TV software. Your TV will automatically upgrade, if your TV need a software
upgrade. If you want to upgrade later, select the Skip. For more information, refer to
"Software Upgrade" (Preference Features → Support Menu) in the e-Manual.
✎
This may take some time, depending on network status.
Press the ▲ or ▼ button to select Home Use, and then press the ENTERE button twice.
Select the Home Use mode. Store Demo mode is for retail environments.
Press the ▲ or ▼ button to select Auto or Manual, and then press ENTERE twice.
✎
If you selected Auto, you'll go to the Time Zone and DST screen. Select Time Zone
or DST, and then press ENTERE. On the Time Zone screen, use the ▲ or ▼
button to select your zone, and then press ENTERE. On the DST screen, press,
ENTERE, then select whether to turn DST (Daylight Savings Time) on or off. When
done, press ENTERE.
✎
If you selected Manual, you'll go to the Date and Time screen. Select Date or Time,
and then press ENTERE. Then, use the number buttons or the ▲ or ▼ button to
set the date or time. Use the ◄ or ► button to move between entry fields. When
done setting the Date and Time, select Next, and then press ENTERE.
Press the ▲ or ▼ button to select Air or Cable, and then press ENTERE. A check
appears on your selection. Select Next, and then press the ENTERE button. You can
check both if you have both connected.
✎
If you selected Cable, you'll go to the Cable System screen. Use the ▲ or ▼
button to select Digital or Analog, and then press. ENTERE. Use the ▲ or ▼
button to select the correct cable signal format - STD, HRC, or IRC - and then press
ENTERE. Most cable systems use STD. Select the correct cable signal format for
both the Digital and Analog systems.
✎
When done, select Next, and the press ENTERE.
The channel search will start automatically. This can take up to 30 minutes.
For more information, refer to Channel → Auto Program in the e-Manual.
✎
Press the ENTERE button at any time to interrupt the memorization process.
If you want to watch a broadcast program, select Close. If you want to enjoy Smart Hub,
select Smart Hub. Smart Hub will start. For more detailed information, refer to "Smart Hub"
in the e-Manual.
English - 9
MENU button on the TV for 5 sec.
POWER
P
INFO
2011-06-29 오전 10:38:23