Table of Contents
Advertisement
To clean the outside of the machine,
wipe off dirt with a cloth dampened in
warm water and mild detergent. Do not
use solvent or petroleum based prod-
ucts to clean the machine .
Carpet Cleaning
Read "Before you begin cleaning"
instructions on page 9.
1. Fill clean solution tank (upper tank)
with HOOVER Carpet/Upholstery
Detergent according to instructions for
Figs. 2-8 to 2-14.
2. Move speed selector to LO for gen-
tle cleaning or Hl for normal cleaning.
3. Dry hands and plug cord into a prop-
erly grounded outlet.
Do not clean over floor electrical out-
lets.
4. To avoid walking on damp carpet,
start at the end of the room farthest from
the door or path to sink where tanks will
be emptied and filled.
Step on handle release pedal and lower
handle to operating position; turn deep
cleaner ON.
3-5
Clean Surge™ Button
The 'Clean Surge' button can be used to
dispense extra solution when cleaning
particularly soiled areas of carpet or spots.
To use, press 'Clean Surge' button while
squeezing solution trigger. For normal
solution spray, release button and contin-
ue to squeeze solution trigger.
Cleaning bare floors
How to attach bare floor
attachment
Disconnect deep cleaner from electri-
cal outlet.
To prevent possible leaking, remove
clean solution tank (Fig. 2-8) and recov-
ery tank (Fig. 2-15) before positioning
bare floor attachment.
Set tanks aside (do not set tank on furni-
ture).
1. With handle in upright position, tilt
cleaner back so that handle rests on the
floor.
10
3-4
5. Squeeze trigger to release cleaning
solution and slowly push deep cleaner
forward (equals one wet stroke).
6. Continue to squeeze trigger and
slowly pull deep cleaner back toward
you (second wet stroke). Release trigger
and slowly push deep cleaner forward
over area just sprayed with solution (dry
stroke). Then slowly pull deep cleaner
back toward you without squeezing trig-
ger (dry stroke).
7. Overlap strokes by 1 inch to help pre-
vent streaking.
Picking up spills
Your deep cleaner may also be used to
pick up small liquid spills (1 gallon or
less, never to exceed 1/4 inch in
depth) on carpet, upholstery, or bare
floors.
1. For best results, pick up spills imme-
diately by placing the stair/upholstery
nozzle just above the spill and suction
up any residue on top of the carpet.
2. If the spill remains, place either the
stair/ upholstery nozzle or floor nozzle
with brushes turned OFF in front of the
spill, pull the nozzle very slowly over the
spill initially with suction only.
Repeat with spray and suction.
3-6
A
B
2. With foam strip (A) (located under the
netting) in position as shown, place
attachment on front of nozzle (B).
Make sure arrow on end of attachment
points in the direction as shown.
Keep nozzle flat on floor for both for-
ward and reverse strokes.
8. For heavily soiled areas, use Clean
Surge™ button (see following section).
To avoid saturating carpet, do not use
more than 4 wet strokes over one
area. Always end with dry strokes.
It is best to alternate wet and dry
strokes as described above.
For best cleaning results and to aid in
faster drying of carpet, end with more
dry strokes. (Continue using dry strokes
until little water is visible passing
through the recovery tank lid.)
Empty recovery tank when the motor
sound becomes higher pitched and
there is a loss in suction (see
"Automatic shut-off", Fig. 2-6)
When finished cleaning, follow "After
cleaning" instructions on pages 9-10.
When picking up spills on bare floors ,
use only the floor nozzle with the bare
floor attachment in place and speed
selector in the OFF position (this will help
p revent spreading the spill).
If a spot is left, the stair/upholstery nozzle is
generally more effective for removing it.
Although no cleaning solution can com-
pletely remove all spots, they can be tre a t-
ed by following the instructions pro v i d e d
by the manufacturer of the carpet, uphol-
s t e ry, or bare floor surface being cleaned.
Do not use the deep cleaner to pick up
f l a m m a ble or combu s t i ble liquids or
ch e m i c a l s .
When finished, follow "After cleaning"
i n s t ructions on pages 9-10.
3-7
3. Push attachment against nozzle while
rotating attachment downward until both
ends snap into place.
( N o t e : Some fo rce may be required to
rotate and snap attachment into place. )
Hide quick links:
Advertisement
Table of Contents
