Variable Frame Rate (Vfr) Recording; Native Vfr Recording; Standard Vfr Recording(Pulldown Recording) - Panasonic AG-HPX301E Operating Instructions Manual

Variable Frame Rate (VFR) Recording

In 720P mode, this camera is capable of frame skipping
(undercranking) and high-speed (overcranking) recording.
The camera operator can select between native (PN)
recording mode and standard (OVER) recording.

Native VFR Recording

1
 IntheSYSTEMSETUPscreen,setthemenu
optionSYSTEMMODEto0-0P(0-
.P)andthemenuoptionRECFORMATto
AVC-I100/PN(0PN,PN).
2
 IntheSCENEFILEscreen,setthemenu
optionVFRtoONandthemenuoptionFRAME
RATEtosuitshootingpurposes.
• T he frame rate can be set to a value beteween
12 frames (12P) to 50 frames (50P) when system
mode is set to 720-50P, and to a value beteween
12 frames (12P) to 60 frames (60P) when system
mode is set to 720-59.94P.
 NOTE
Pressing the SYNCHRO SCAN switch while the JOG
dial button is held down and the frame rate indication
is blinking allows you to change the frame rate as long
as recording is not in progress.
3
 PresstheRECbutton.
This starts recording in the VFR mode (native VFR).
This mode can be combined with the AVC-I 100, AVC-I 50,
DVCPRO HD, 25PN (30PN, 24PN) recording formats.
For details, refer to [List of recording, playback and output
formats] (page 49).
For details, refer to [SYSTEM SETUP screen] (page 131).
 NOTE
Note the following about native VFR recording.
- T he P2 card that is being recorded cannot be changed
during recording.
- P re-recording, loop recording, interval recording and one-
shot recording are not available.
- 1 394 output is not available during recording and recording
standby.
- C hanging Scene Dial position during recording does not
change VFR on and off position.
- S ound cannot be recorded.
- T he time code is locked to Rec Run.
- T humbnail screens are created 1 frame later than video
recorded on a P2 card, but this is not a malfunction.
*1 I n 25PN (30PN, 24PN) recording modes, when the frame rate is
25 (30, 24) frames per second, respectively, audio can also be
recorded. The time code can be set to Free Run (F-RUN).

*1
*1
Standard VFR recording
(pulldown recording)
1
 IntheSYSTEMSETUPscreen,setthemenu
optionSYSTEMMODEto0-0P(0-
.P)andthemenuoptionRECFORMATto
AVC-I100/0P(0P).
2
 IntheSCENEFILEscreen,setthemenu
optionVFRtoONandthemenuoptionFRAME
RATEtosuitshootingpurposes.
• T he frame rate can be set to a value beteween
12 frames (12P) to 50 frames (50P) when system
mode is set to 720-50P, and to a value beteween
12 frames (12P) to 60 frames (60P) when system
mode is set to 720-59.94P.
 NOTE
Pressing the SYNCHRO SCAN switch while the JOG
dial button is held down and the frame rate indication
is blinking allows you to change the frame rate without
opening a setting menu as long as recording is not in
progress.
3
 PresstheRECbutton.
This starts recording in the VFR mode (OVER 50P
(60P)).
This mode can be combined with the AVC-I 100/50P (60P),
AVC-I 50/50P (60P) and DVCPRO HD/50P (60P) recording
formats.
For details, refer to [List of recording, playback and output
formats] (page 49).
For details, refer to [SYSTEM SETUP screen] (page 131).
Setting a low frame rate and recording a fast-moving
subject at 50P (60P) will produce a smoothly flowing
sequence at playback.
 NOTE
• A udio playback is disabled when a frame rate converter is
used to extract active frames for over and under-cranking.
• N ote the following about standard VFR recording.
- T he P2 card that is being recorded cannot be changed
during recording.
- P re-recording, loop recording, interval recording and one-
shot recording are not available.
- 1 394 output is available during recording and recording
standby, but not in AVC Intra mode.
- C hanging Scene Dial position during recording does not
change VFR on and off position.
- S ound is recorded.