Panasonic AG-HPX301E Operating Instructions Manual page 21

20 P2 CARD ACCESS LED
This LED indicates the recording and playback status of
each card.
For details, refer to [P2 CARD ACCESS LED and status
of P2 cards]. (page 29)
21 GENLOCK IN connector
This connector inputs a reference signal when the
camera unit is gen-locked, or when the time code is
externally locked.
 NOTE
• S upply an HD Y signal (1080/50i (59.94i), 720/50P (59.94P))
or a composite signal (576/50i (480/59.94i)) as input
reference signal. The subcarrier of VIDEO OUT connector
output (composite signal) cannot be externally locked. In
SD mode, the signal will not lock to the HD signal.
22 REMOTE connector
Some functions can be remote controlled when the
remote control unit AJ-RC10G (optional accessory) is
connected to the camera.
For details, refer to [Connecting the AJ-RC10G Remote
Controller] (page 105).
23 VIDEO OUT connector
This connector outputs video signals.
• I n HD mode, down-converted composite video
signals are output.
• U se the menu option DOWNCON MODE in the
OUTPUT SEL screen to set signal output. (The factory
setting is LETTER BOX.)
24 SD memory card slot
Insert an SD memory card (optional accessory) in this
slot. It is used for recording and loading camera setting
menus or lens files, uploading meta data and recording
proxies (optional).
 NOTE
SD memory card precautions
• U se only SD memory cards that conform to the SD
standard or the SDHC standard in this camera.
• M ultiMediaCards (MMC) cannot be used. (Use of such
cards may prevent recording.)
• B e sure to use mini SD card adapters when using mini
SD cards with this camera. (Note that this camera will
not operate normally when a mini SD adapter is installed
without inserting a card. Be sure to insert a card when an
adapter is installed.)
• U se of Panasonic SD memory cards and mini SD cards
is recommended. Be sure to format such cards in this
camera.
• T his unit supports the following SD and SDHC memory
card capacities.
SD memory cards
SDHC memory
cards
For proxy (optional) recording, use 256 MB, 512 MB, 1 GB,
2 GB SD memory cards labeled "High Speed" or SDHC
memory cards.
8MB/16MB/32MB/64MB/
128MB/256MB/512MB/1GB/
2GB
4GB/6GB/8GB/12GB/16GB/
32GB
• F or the latest information not available in the Operating
Instructions, visit the P2 Support Sites at the following
Web site.
https://eww.pavc.panasonic.co.jp/pro-av
About SD and SDHC memory cards
• T he SDHC card is a new standard, established by the
SD Card Association in 2006, for memory cards with
capacities of 2 GB or more.
• The SD logo is a registered trademark.
• M MC (MultiMediaCard) is a registered trademark of
Infineon Technologies AG.
25 BUSY (operation mode display) lamp
This lamp indicates the active status of the SD memory
card. It stays illuminated when the card is active.
 NOTE
Do not remove the card while the lamp is on.
The SD memory card could be damaged.
26 DVCPRO/DV connector
An IEEE1394 standard connector for input and output of
video, audio and data.
For details, refer to [Connections to the DVCPRO/DV
Connector] (page 151).
27 SDI OUT 1 connector
28 SDI OUT 2 connector
• T his connector outputs SDI signals.
• U se the menu option SDI SELECT in the OUTPUT
SEL screen to select AUTO, 1080i or 576i (480i). This
connector does not support up-conversion.
It outputs the same signals as SDI OUT.
29 SCENE FILE dial
This dial allows you to select and load shooting
conditions from the scene files prerecorded to each of
the six positions.
 NOTE
During recording, selecting a position with a different
frame rate will not change the frame rate until the camera
is set to recording standby mode.
For details, refer to [How to use Scene File Data] (page 87).
30 FOCUS ASSIST button
Turns magnification of the center portion of the image
on and off.
For details, refer to [Focus assist function] (page 80).
31 REC switch
Switches functions of the REC button on the handle.
ON: Enables the REC button.
OFF: Disables the REC button.
32 USB lamp
This lamp lights when the camera is in USB mode (PC
mode).
1