Page 1
Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MWM-7300 Retain This Manual for Reference 09-15-08 OWNER'S MANUAL MARCY HOME GYM MWM-7300 IMPEX 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com...
ORDERING PARTS...………… 25 BEFORE YOU BEGIN ® Thank you for selecting the Marcy Home Gym MWM-7300 by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory.
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
Page 4
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Base Frame and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts until instructed to do so.
Page 9
STEP 2 (See Diagram 2) A.) Slide two Ø 2 ½” x 1” Rubber Bumpers (#65) onto the Guide Rods (#18). Attach the two Guide Rods onto the Weight Stack Frame (#17). Secure the bottom of Guide Rods with two M10x 1” Allen Bolts (#82) and two Ø ¾” Washers (#91). B.) Pull the top of the two Guide Rods off the Weight Stack Frame.
Page 11
STEP 3 (See Diagram 3) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Lower Cross Brace (#16) to the Weight Stack Frame (#17). Secure them with two M10 x 3 1/8” Carriage Bolts (#72), one 5 1/8” x 1 5/8” Bracket (#58), two Ø ¾” Washers (#91), and two M10 Aircraft Nuts (#94).
Page 13
STEP 4 (See Diagram 4) A.) Attach the Right & Left Seat Swivel Frame (#13) & (#14) to Main Base Frame (#1) from each side. Secure them together with one M12 x 7 7/8” Allen Bolt (#74), two Ø 1” Washer (#90), and one M12 Aircraft Nut (#93).
Page 15
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 205” Upper Cable (#35) to the opening at the front of the Upper Frame (#5). Note: The Ball Stopper on the cable need to be underneath the Frame. B.) Attach a Pulley (#51) to the opening.
Page 17
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach the 118” Lower Cable (#36) to the opening on the bottom of the Leg Developer (#10). B.) Attach a Pulley (#51) to the opening. Secure it with one M10 x 3 3/8” Allen Bolt (#78), two Ø...
Page 19
STEP 7 (See Diagram 7) A.) Attach the Front Weight Stack Cover (#29) to the Weight Stack Frame (#17). Secure it with six M6 x 2 ½” Philips Screws (#89) and six Cover Spacers (#54). B.) Repeat the Procedure A to install the Rear Weight Stack Cover (#30) to the other side. DIAGRAM 7...
Page 20
A.) Attach the Backrest Board (#34) to Front Vertical Frame (#2). Secure it with two M8 x 2 1/8” Allen Bolts (#85) and two Ø 5/8” Washers (#92). B.) Attach the Seat Pad to Seat Support (#11). Secure it with two M8 x 2 1/8” Allen Bolts (#85) and two Ø...
Page 22
A.) Attach the Front Press (#6) to the Front Press Base (#5). Secure it with one 8 ¾” Long Axle (#57), two Ø ¾” Washers (#91), and two M10 Aircraft Nuts (#94). Do not over tighten the Nuts. Make sure the Front Press is able to swivel smoothly. B.) Use the T-shaped Lock Pin (#40) to lock the Front Press to the Front Press Base in desired position.
PARTS LIST KEY NO. DESCRIPTION Main Base Frame Front Vertical Frame Rear Vertical Frame Upper Frame Front Press Base Front Press Foot Plate Leg Press Frame Arm Curl Stand Leg Developer Seat Support Front Seat Swivel Frame Right Seat Swivel Support Left Seat Swivel Support Upper Cross Brace Lower Cross Brace...
MWM-7300 WEIGHT RESISTANCE CHART Station Lat Pull Front Press Low Pulley Leg Developer Leg Press Station Lat Pull Front Press Low Pulley Leg Developer 141 Leg Press Note: Each plate weights 10 lbs. Numbers are approximate. Actual weights may vary.
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes.