Page 1
Please read all instructions carefully before using this product Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model AB 4000 Retain This Manual for Reference 02-21-02 OWNER'S MANUAL MARCY AB BENCH AB 4000 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com...
WARRANTY...… 12 ORDERING PARTS... 12 BEFORE YOU BEGIN Thank you for selecting the MARCY AB Bench AB4000 by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#1) to the Front Stabilizer (#2). Align the holes and secure it with three M10 x 5/8”...
Page 6
STEP 2 (See Diagram 2) A.) Attach two Bushings (#23) to each Seat Support Frames (#6). B.) Attach one Backrest Support (#7) to the Seat Support Frame (#6). Align the holes and secure them with one M10 x 1 5/8” Allen Bolt (#32), and one procedure to install the other side.
Page 7
STEP 3 (See Diagram 3) A.) Align the holes on the two Backrest Supports (#7) to the pivot on the Sliding Block (#9). Secure them with one M10 x 6 ¼” Allen Bolt (#35), two (#41). DIAGRAM 3 ¾” Washers (#39), and one M10 Aircraft Nut...
Page 8
STEP 4 (See Diagram 4) A.) Attach the Seat Incline Support Bracket (#8) to the Main Frame (#1). Secure it with one M10 x 4 3/4” Allen Bolt (#34), two tighten the nut and bolt. The Bracket needs to be able to swivel. Attach two bushings (#23) to the pivot on the Seat Incline Support Bracket (#8).
Page 10
STEP 5 (See Diagram 5) A.) Place the Seat Pad (#14) onto the Seat Support Frames (#6). Align the holes and secure it with four M8 x 2” Allen Bolts (#37) and B.) Place the Backrest Board (#15) onto the Backrest Supports (#7). Align the holes and secure it with four M8 x 2”...
Page 12
STEP 6 (See Diagram 6) A.) Insert the Leg Developer Holder (#4) into the opening in front of the Seat. Secure it with a Lock Knob underneath the Seat. Attach the Leg Developer (#5) to the bracket on the Leg Developer Holder (#4).
PARTS LIST KEY NO. DESCRIPTION Main Frame Front Stabilizer Rear Stabilizer Leg Developer Holder Leg Developer Seat Support Frame Backrest Support Seat Incline Support Bracket Sliding Block Incline Adjustment Bar Foam Tube Axle Olympic Sleeve Seat Pad Backrest Pad Leg Developer Bushing Arm Curl Stand 1 ½”...
No other warranty beyond that specifically set forth above is authorized by IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.