Focus Adjustment; Focus Control Adjustment - Sony KP-53V100 Service Manual

2-4. FOCUS ADJUSTMENT

In this adjustment, use the remote commander while in service
mode. For details on the usage of the service mode and the remote
commander, please refer the item 2-9. ELECTRICAL ADJUSTMENTS
BY REMOTE COMMANDER.
1. Loosen the lens wing nut.
2. Enter the service mode.
3. Display a white raster.
4. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off
the CRTs individually without using lens caps).
5. Select adjustment category "PJE", then press 6 to display the test
signal (crosshatch)*.
* Every time 6 is pressed, the test signal changes to: "crosshatch+video
signal" → "dots+video signal" → "crosshatch only" → "dots only" → black
screen → "crosshatch+video signal" → ....etc.
6. Rotate the green lens assembly to adjust to the optimum focus point
with the test signal being displayed
7. Tighten the lens wing nut.
8. Cover the green and blue CRT lenses with the lens caps to allow only
red to show (or use the method shown in the note below for turning
off the CRTs individually without using lens caps).
9. Make sure the cross-hatch is still being displayed; if not, follow step 5
above.
10. Adjust the red CRT lens the same way as the green CRT lens.
11. Cover the green and red CRT lenses with the lens caps to allow only
blue to show (or use the method shown in the note below for turning
off the CRTs individually without using lens caps).
12. Make sure the cross-hatch is still being displayed; if not, follow step
# 5 above.
13. Adjust the blue CRT lens the same way as the green and red CRT
lenses.
14. After adjusting the items 2-5 "Focus VR Adjustment", 2-6 "2-Pole
Magnet Adjustment" and 2-7 "4-Pole Magnet Adjustment", reconfirm
the optimum focus point and adjust again if necessary.
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams in the service mode by individually changing the data from "1" to
"0" in category VPNT, item 28 RON (red), item 29 GON (green), or item
30 BON (blue).
Test Signal

2-5. FOCUS CONTROL ADJUSTMENT

1. Enter the service mode.
2. Display a white raster.
3. Cover the red and blue CRT lenses with lens caps to allow only green
to show (or use the method shown in the note below for turning off
the CRTs individually without using lens caps).
4. Select adjustment category "PJE", then press 6 to display the test
signal (crosshatch)*.
* Every time 6 is pressed, the test signal changes to: "crosshatch+video
signal" → "dots+video signal" → "crosshatch only" → "dots only" → black
screen → "crosshatch+video signal" → ....etc.
5. Adjust the green focus control on the focus block to achieve the
optimum focus point with the test signal being displayed.
6. Cover the green and blue picture lenses with lens caps to allow only
red to show (or use the method shown in the note below for turning
off the CRTs individually without using lens caps).
7. Make sure the cross-hatch is still being displayed; if not, follow step 4
above.
8. Adjust the red focus control on the focus block to achieve the optimum
focus point with the test signal being displayed.
9. Cover the green and red picture lenses with lens caps to allow only
blue to show (or use the method shown in the note below for turning
off the CRTs individually without using lens caps).
10. Make sure the cross-hatch is still being displayed; if not, follow step
# 4 above.
11. Adjust the blue focus control on the focus block to achieve the
optimum focus point with the test signal being displayed.
12. Repeat steps 1 through 11 after adjusting items 2-4. "Focus Lens
Adjustment", 2-6 "2-pole Magnet Adjustment", 2-7 " 4-Pole Magnet
Adjustment"
Note: If lens caps are unavailable, you can cut off the unnecessary color
beams in the service mode by individually changing the data from "`" to
"0" in category VPNT, item 28 RON (red), item 29 GON (green), or item
30 BON (blue).
Lens
— 16 —
KP-53V100
Scanning line visible.
A
Minimize both A and B.
B
Center of crosshatch