How do I use my Whirlpool dehumidifier?

To use your dehumidifier:Plug it into a grounded three-prong outlet.Press POWER to turn on the dehumidifier.Press FAN to choose the fan speed.Press MODE to choose the mode.Press the plus or minus arrow button to choose the level of humidity.Press POWER to turn off the dehumidifier. The dehumidifier will retain your last settings. For more information, see page 5 of the manual.

Why is my Whirlpool dehumidifier not collecting water?

If your dehumidifier runs but does not dehumidify, consider the following:All models have an automatic de-icer that will shut off the compressor and allow the fan to run. The compressor will cycle back on when the de-icer senses the correct operating temperature.If the control is set to Continuous and the humidity level is low, little or no water may be collected.The filter may be dirty or obstructed by debris. Clean the filter. For more information, see page 11 of the manual.

How do I clean the filter on my Whirlpool dehumidifier?

To clean the air filter on your dehumidifier:Turn off the dehumidifier.Remove the bucket.Pull the air filter down from below the front louvres.Pull the bottom edge of the air filter away from the dehumidifier to clear the bottom.Use a vacuum cleaner to clean the air filter. If it is dirty, wash it in warm water with a mild detergent. Do not wash the air filter in the dishwasher or use any chemical cleaners. Air dry the filter completely before replacing it.Slide the air filter up into the dehumidifier.Reinstall the bucket.Turn on the dehumidifier.

Why does my Whirlpool dehumidifier freeze up?

All models have an automatic de-icer that will shut off the compressor and allow the fan to run to reduce ice build-up on the coils. The compressor will cycle back on when the de-icer senses the correct operating temperature.

What is the optimal humidity level to set on my Whirlpool dehumidifier?

The humidity can be adjusted between 30% Relative Humidity and 80% Relative Humidity. In Auto Dry mode, the Desired Humidity is set to 50% automatically.

How do I clean my Whirlpool dehumidifier?

To clean your dehumidifier:Air Filter: Turn off the dehumidifier, remove the bucket, pull down and away the air filter, clean it with a vacuum cleaner or wash with mild detergent, air dry completely, then slide it back in and reinstall the bucket. Check the filter every two weeks.Exterior: Turn off the dehumidifier, then dust the front grille and side panels with a soft brush or the dusting attachment of your vacuum cleaner.Water Bucket: Every few weeks, rinse the inside of the water bucket with a mild detergent to avoid the growth of mold, mildew, and bacteria. For more information, see page 10 of the manual.

How do I set up continuous drainage using a drain hose on my Whirlpool dehumidifier?

There are two options for continuous drainage: Option 2: Connect Drain HoseRemove screws from the connector cover.Attach a garden hose to the drain hose connector of the dehumidifier and hand tighten it. The hose is sold separately.Place the other end of the garden hose into a floor drain, ensuring the hose lies flat and is in the drain.Option 3: PUMP-Drain (for Pump function model only)This feature allows you to pump water horizontally or vertically with a 16-foot hose. You must connect the drain hose (with connector B) to drain hose connector A before pressing the Pump button. Press PUMP to activate the pump system for active drainage. The pump light will switch on. If the pump light flashes, it means the pump is not functioning properly. If the drain hose is not correctly connected or is bent, the pump light will flash and the pump system will not work. Refer to "Trouble shooting" for direction.

What should I do if the pump on my Whirlpool dehumidifier is not working?

If the pump light flashes, it indicates that the pump is not functioning properly. This can happen if the drain hose is not correctly connected to the unit or is bent. To troubleshoot:Check and make sure the drain hose is correctly connected to the unit.Press the POWER button to turn off the unit. Restart the unit by pressing the POWER button again.

What do the error codes on my Whirlpool dehumidifier indicate?

If the dehumidifier displays a trouble code such as E1, E2..., the unit will still work, but you should contact customer service.

How frequently should I clean the filter on my Whirlpool dehumidifier?

You should check the filter every two weeks to see whether it needs cleaning. The Filter Monitor indicator light will remain on for 180 hours or until you press FILTER MONITOR to reset it. For more information, see pages 7 and 10 of the manual.

Why is my Whirlpool dehumidifier making unusual noises?

When your dehumidifier is operating normally, you may hear certain sounds:Compressor sounds, which may be loud. This is normal.Air movement from the fan.Pump sounds, which may be loud. This is normal.Clicking sounds when the dehumidifier or compressor turns off and on, and when the Automatic Shut-off Switch is working. For more information, see page 9 of the manual.

Can a Whirlpool dehumidifier be used in a cold basement?

You should install the dehumidifier in an area where the temperature will not fall below 38 °F (3 °C), as lower temperatures will cause performance to drop. The dehumidifier also has an automatic de-icer that will turn off the compressor if a low temperature condition exists, and the compressor will cycle back on when the de-icer senses the correct operating temperature.

Can a Whirlpool dehumidifier run continuously without issues?

Yes, you can set the dehumidifier to Continuous mode, which will operate the dehumidifier continuously. In this mode, the fan speed can be adjusted, but the desired humidity cannot be adjusted, and the LED display will show the room humidity level.

How do I empty the water collection bucket on my Whirlpool dehumidifier?

To empty the water collection bucket:Grasp the bucket sides to slide out the bucket.Grasp the handle and bottom of the bucket to lift it.Pour water through the opening into a sink or tub.Replace the handle and reinstall the bucket. For more information, see page 8 of the manual.

How accurate is the humidity sensor on a Whirlpool dehumidifier?

The humidity displayed is only for reference. For accurate humidity, you should check a hygrometer.

What is the recommended operating temperature range for a Whirlpool dehumidifier?

The minimum operating temperature for the dehumidifier is 38 °F (3 °C). You should install the dehumidifier in an area where the temperature will not fall below 38 °F (3 °C) because lower temperatures will cause performance to drop.