Download Print this page

Adjusting Setup Items; Connecting With Bluetooth Device/Smartphone - Sony MEX-N4000BT Quick Manual

Hide thumbs Also See for MEX-N4000BT:

Advertisement

BLUETOOTH
BLUETOOTH
Connecting with a BLUETOOTH
Connecting with a Smartphone
device
by One touch (NFC)
To use a paired device, connection with this unit
By touching the control dial on the unit with an
is required. Some paired devices will connect
NFC* compatible smartphone, the unit is paired
automatically.
and connected with the smartphone
automatically.
* NFC (Near Field Communication) is a technology
enabling short-range wireless communication
between various devices, such as mobile phones and
IC tags. Thanks to the NFC function, data
1
Press CALL, rotate the control dial to select
communication can be achieved easily just by
[BT SIGNL], then press it.
touching the relevant symbol or designated location
Make sure that
lights up.
on NFC compatible devices.
2
Activate the BLUETOOTH function on the
For a smartphone with Android OS 4.0 or lower
BLUETOOTH device.
installed, downloading the app "NFC Easy
Connect" available at Google Play™ is required.
3
Operate the BLUETOOTH device to connect
The app may not be downloadable in some
to this unit.
countries/regions.
or
lights up.
1
Activate the NFC function on the
To connect the last-connected device from
smartphone.
this unit
For details, refer to the operating instructions
Activate the BLUETOOTH function on the
supplied with the smartphone.
BLUETOOTH device.
2
Press SRC.
Touch the N-Mark part of the unit with the
Select [BT PHONE] or [BT AUDIO].
N-Mark part of the smartphone.
Press ENTER to connect with the cellular phone,
or PAUSE to connect with the audio device.
Note
While streaming BLUETOOTH audio, you cannot connect
from this unit to the cellular phone. Connect from the
cellular phone to this unit instead.
Tip
Make sure that
lights up on the display of
With BLUETOOTH signal on: when the ignition is turned
the unit.
to on, this unit reconnects automatically to the
last-connected cellular phone.
To disconnect by One touch
To install the microphone
Touch the N-Mark part of the unit with the
Installing the microphone (not supplied) will
N-Mark part of the smartphone again.
improve audio quality while talking through this
Notes
unit. For details on how to connect the
ˎ When making the connection, handle the
ˎ
microphone, refer to the operating instructions
smartphone carefully to prevent scratches.
ˎ One touch connection is not possible when the unit is
ˎ
supplied with the microphone.
already connected to another NFC compatible device.
In this case, disconnect the other device, and make
connection with the smartphone again.
BLUETOOTH
BT SIGNL*
1
(BLUETOOTH signal)
Operating the BLUETOOTH
Activates the BLUETOOTH function: [ON], [OFF].
functions
BT INIT*
4
(BLUETOOTH initialize)
Initializes all the BLUETOOTH related settings
1
(pairing information, preset number, device
Press CALL.
information, etc.).
The call menu appears.
2
*
You can also select these items by pressing MENU
Rotate the control dial to select the desired
1
and rotating the control dial to select [BT].
item, then press it.
*
2
When connecting to a cellular phone supporting
3
Press
(back)*.
PBAP (Phone Book Access Profile).
The source returns to the BLUETOOTH phone.
*
3
Depending on the cellular phone, this unit's ringtone
may be output even if set to [2] (cellular phone).
* For PAIRING, REDIAL, VOICE DIAL and BT SIGNL
*
4
Appears on the setup menu when the unit is turned
settings, step 3 is not necessary.
off.
The following items can be set:
PAIRING*
1
Turns this unit into standby mode for pairing with
BLUETOOTH devices.
PHONEBOOK
Makes a call to the number selected by the user
from the phonebook*
2
.
REDIAL
Makes a call again to the last phone number
dialed.
RECENT CALL
Allows the user to select a phone number from
the call history and redial that number*
2
.
VOICE DIAL
Activates voice dialing, and allows the user to
make a call by saying its voice tag.
DIAL NUMBER
Makes a call to the phone number entered by the
user.
RINGTONE*
1
*
3
Selects whether this unit or the connected cellular
phone outputs the ringtone: [1] (this unit), [2]
(cellular phone).
AUTO ANS*
1
(auto answer)
Sets this unit to answer an incoming call
automatically: [OFF], [1] (about 3 seconds), [2]
(about 10 seconds).
AUTO PAIRING*
1
Start BLUETOOTH pairing automatically when iOS
device version 5.0 or later is connected via USB:
[ON], [OFF].
SET UP
RADIO
CD
USB
iPod
BLUETOOTH
POSITION (listening position)
Adjusting the sound
characteristics
1
During reception/playback, press MENU,
rotate the control dial to select [SOUND],
then press it.
2
Rotate the control dial to select the desired
SET F/R POS (set front/rear position)
item, then press it.
Simulates a natural sound field by delaying the
sound output from front/rear speaker to suit your
3
Rotate the control dial to select the setting,
position.
then press it.
FRONT L (): Front left
The setting is complete.
FRONT R (): Front right
4
FRONT (): Center front
Press
(back) to return to the previous
ALL (): In the center of your car
display.
CUSTOM: Position set by App Remote
OFF: No position set
The following items can be set depending on
ADJ POSITION*
1
(adjust position)
the source and setting:
Fine-tunes the listening position setting.
SOUND Setup:
Adjustable range: [+3] – [CENTER] – [-3].
SET SW POS*
(set subwoofer position)
1
C.AUDIO+ (clear audio+)
NEAR (): Near
Reproduces sound by optimizing the digital signal
NORMAL (): Normal
with the Sony recommended sound settings:
FAR (): Far
[ON], [OFF]. (Automatically sets to [OFF] when
[EQ10 PRESET] is changed).
BALANCE
Adjusts the sound balance: [RIGHT-15] – [CENTER]
EQ10 PRESET
– [LEFT-15].
Selects an equalizer curve from 10 equalizer
curves or off: [R AND B], [ROCK], [POP], [DANCE],
FADER
[HIP-HOP], [ELECTRONICA], [JAZZ], [SOUL],
Adjusts the relative level: [FRONT-15] – [CENTER]
[COUNTRY], [CUSTOM], [OFF].
– [REAR-15].
The equalizer curve setting can be memorized for
DSEE (digital sound enhancement engine)
each source.
Improves digitally compressed sound by restoring
EQ10 SETTING
high frequencies lost in the compression process.
Sets [CUSTOM] of EQ10.
This setting can be memorized for each source
BASE
other than the tuner.
Selects a preset equalizer curve as a basis for
Selects the DSEE mode: [ON], [OFF].
further customizing: [BAND1] 32 Hz, [BAND2] 63
LOUDNESS
Hz, [BAND3] 125 Hz, [BAND4] 250 Hz, [BAND5] 500
Reinforces bass and treble for clear sound at low
Hz, [BAND6] 1 kHz, [BAND7] 2 kHz, [BAND8] 4 kHz,
volume levels: [ON], [OFF].
[BAND9] 8 kHz, [BAND10] 16 kHz.
The volume level is adjustable in 1 dB steps, from
AAV (advanced auto volume)
Adjust the playback volume level of all playback
-6 dB to +6 dB.
sources to the optimum level: [ON], [OFF].
RB ENH*
2
(rear bass enhancer)
HPF (high pass filter)
Rear Bass Enhancer enhances the bass sound by
HPF FREQ (high pass filter frequency)
applying a low pass filter setting to the rear
Selects the front/rear speaker cut-off frequency:
speakers. This function allows the rear speakers
[OFF], [50Hz], [60Hz], [80Hz], [100Hz], [120Hz].
to work as a subwoofer if one is not connected.
HPF SLOP (high pass filter slope)
(Available only when [SW DIREC] is set to [OFF].)
Selects the HPF slope (effective only when [HPF
RBE MODE (rear bass enhancer mode)
FREQ] is set to other than [OFF]): [1], [2], [3].
Selects the rear bass enhancer mode: [1], [2], [3],
AUX VOL*
4
(AUX volume level)
[OFF].
Adjusts the volume level for each connected
LPF FREQ (low pass filter frequency)
auxiliary device: [+18 dB] – [0 dB] – [-8 dB].
Selects the subwoofer cut-off frequency: [50Hz],
This setting negates the need to adjust the
[60Hz], [80Hz], [100Hz], [120Hz].
volume level between sources.
LPF SLOP (low pass filter slope)
BTA VOL*
5
(BLUETOOTH audio volume level)
Selects the LPF slope: [1], [2], [3].
Adjusts the volume level for each connected
SW DIREC*
3
(subwoofer direct connection)
BLUETOOTH device: [+6 dB] – [0 dB] – [-6 dB].
You can use the subwoofer without a power
This setting negates the need to adjust the
amplifier when it is connected to the rear speaker
volume level between sources.
cord. (Available only when [RBE MODE] is set to
[OFF].)
*
1
Does not appear when [SET F/R POS] is set to [OFF].
Be sure to connect a 4 - 8 ohm subwoofer to
*
2
When [SW DIREC] is set to [OFF].
either of the rear speaker cords. Do not connect a
*
3
When [RBE MODE] is set to [OFF].
speaker to the other rear speaker cord.
*
4
When the AUX is selected.
SW MODE (subwoofer mode)
*
5
When BLUETOOTH audio source is activated.
Selects the subwoofer mode: [1], [2], [3], [OFF].
SW PHASE (subwoofer phase)
Note
Selects the subwoofer phase: [NORM], [REV].
These settings are not available for a BLUETOOTH
SW POS*
1
(subwoofer position)
phone source.
Selects the subwoofer position: [NEAR],
[NORMAL], [FAR].
LPF FREQ (low pass filter frequency)
Selects the subwoofer cut-off frequency: [50Hz],
[60Hz], [80Hz], [100Hz], [120Hz].
LPF SLOP (low pass filter slope)
Selects the LPF slope: [1], [2], [3].
S.WOOFER (subwoofer)
SW LEVEL (subwoofer level)
Adjusts the subwoofer volume level:
[+10 dB] – [0 dB] – [-10 dB].
([ATT] is displayed at the lowest setting.)
SW PHASE (subwoofer phase)
Selects the subwoofer phase: [NORM], [REV].
SW POS*
1
(subwoofer position)
Selects the subwoofer position: [NEAR],
[NORMAL], [FAR].
LPF FREQ (low pass filter frequency)
Selects the subwoofer cut-off frequency: [50Hz],
[60Hz], [80Hz], [100Hz], [120Hz].
LPF SLOP (low pass filter slope)
Selects the LPF slope: [1], [2], [3].
Location of controls and basic operations / Detaching the front panel /
Setting the clock / Storing stations automatically /
Playing back an iPod/USB device / Playing tracks in various modes /
Pairing and connecting with a BLUETOOTH device
SET UP
RADIO
CD
USB
iPod
BLUETOOTH
*
1
When the unit is turned off.

Adjusting setup items

*
2
Does not appear in App Remote.
*
3
When FM is received.
1
*
When the tuner is selected.
Press MENU, rotate the control dial to
4
select the desired category, then press it.
SOUND Setup:
2
For details, see "Adjusting the sound
Rotate the control dial to select the desired
characteristics."
item, then press it.
3
DISPLAY Setup:
Rotate the control dial to select the setting,
then press it.*
DEMO (demonstration)
The setting is complete.
Activates the demonstration: [ON], [OFF].
4
DIMMER
Press
(back) to return to the previous
Changes the display brightness: [ON], [OFF].
display.
ILLUM (illumination)
* For CLOCK-ADJ and BTM settings, step 4 is not
Changes the illumination color: [1], [2].
necessary.
AUTO SCR* (auto scroll)
The following items can be set depending on
Scrolls long items automatically: [ON], [OFF].
the source and setting:
* When the CD, USB or BLUETOOTH audio is selected.
GENERAL Setup:
CLOCK-ADJ (clock adjust)
BT (BLUETOOTH):
Adjust clock.
For details, see "Operating the BLUETOOTH
functions."
CAUT ALM*
1
(caution alarm)
Activates the caution alarm: [ON], [OFF].
APP REM (App Remote):
(Available only when the unit is turned off.)
Starts establishing App Remote.
BEEP
Activates the beep sound: [ON], [OFF].
AUTO OFF
Shuts off automatically after a desired time when
the unit is turned off: [NO], [30S] (30 seconds),
[30M] (30 minutes), [60M] (60 minutes).
AUX-A*
*
(AUX audio)
1
2
Activates the AUX source display: [ON], [OFF].
(Available only when the unit is turned off.)
REAR/SUB
Switches the audio output: [SUB-OUT]
(subwoofer), [REAR-OUT](power amplifier).
(Available only when the unit is turned off.)
CT (clock time)
Activates the CT function: [ON], [OFF].
REGIONAL*
3
Restricts reception to a specific region: [ON],
[OFF]. (Available only when FM is received.)
BTM*
4
Stores radio stations automatically.

Hide quick links:

Advertisement

loading