In Case Of Difficulty - Kenwood VR-6060 Instruction Manual

In case of difficulty
Resetting the Microcomputer
The microcomputer may malfunction (unit cannot be operated, or
shows an erroneous display) if the power cord is unplugged while
the power is ON, or due to some other external factor. If this
happens, execute the following procedure to reset the microcom-
puter and return the unit to its normal operating condition.
For the U.S.A. and Canada
Unplug the power cord from the wall outlet, then plug it
back in while holding down the POWER ON/STANDBY
0 key.
For other countries
With the power cord plugged in, turn the POWER ON/
OFF key OFF. Then, while holding down the ON/
STANDBY 0 key, press POWER ON/OFF.
l
Please note that resetting the mtcrocomputer will clear the contents
of the memory and returns the unit to the state It was I" when It left
the factory.
Amplifier
SVhptctm
No sound from the speakers.
l
The speaker cords are disconnected
*VOLUME IS set to the minimum position
. MUTE IS ON
*The SPEAKERS switches are set to OFF
l
Speaker cords are short-cIrcuited
l
Connect them properly referring to "Conl?ect-
trig the speakers"
- 14
l
Adlust the volume to a propel level
l
Turn OFF the MUTE
- 2%
l
Set the SPEAKERS switches to ON - 22.
l
Turn the power off, elimnate the shot t-ciicult-
~ng. then turn on the power agal,,
The standby indicator blinks and sound is
not output.
l
The speaker cord IS disconnected
l
Connect It properly referring to "Connecting
the speakers"
- 14
Sound is not output from the surround
speakers and I or the center speaker, or their
sound is very small.
l
The surround speaker cords and/at the center
speaker cord IS dlsconnected
l
A surround mode has not been engaged
l
The surround and/or center volume controls
are set to the mlnlmum level
l
The audio cord from the record player IS Inot
connected to the PHONO lacks
l
The record player IS Inot grounded
l
Connect It properly refet ring to "Coivectlng
the speakers"
- 14-
l
Select a surround mode
l
Adlust the speaker levels using tile test tone
- 21
l
Insert the audio cold plugs securely Into the
PHONO lacks
l
Connect the grounding wire to the GhlD terms-
nal on the rear panel
A humming noise is generated when the
PHONO input selector is selected.
When playing a Dolby Digital source signal
using a DVD player, the sound is cut off soon
after it starts.
l
There are many possible causes for this prob-
lem, depending on the type of DVD player
used
l
Set the input mode to dIgItal manual before
starting playback of the Dolby DIgital source
- 8
No sound is produced during playback from
a DVD player.
l
The Input mode IS set to dIgital manual
l
Press the INPUT MODE key to select to full
auto mode
- a-
A video source cannot be recorded
normally.
l
The software IS copy-guarded
l
Copy-guarded video softwate cannot be re-
corded
Tuner
--- -..... ,x,-.. ^._ ,xxxxx. .^^^^
l
No antenna IS connected
l
The broadcast band IS not set properly
*The frequency of the desired station IS not
tuned
l
Connect an antenna
- 16
l
Set the broadcast band propel ly
*Tune the frequency of the desired statloh
- 26
l
Noise due to lgnitlon noise from an automo-
bile
*Noise due to Interference from al? electric
appliance
l
Noise due to a nearby TV set
Interference.
l
Install the outdoor antenna away from the
road.
*Turn off the power to the appliance
l
Install th& receiver farther away frov the TV
l
Preset a station with a iece~vable frequency
l
Preset the statlon again
l
The preset statjon belongs to a frequency that
cannot be received
*The preset memory was cleared because the
power cord had been icnplugged for a long
period of time
A station which was preset cannot be re-
ceived by pressing the corresponding nu-
meric key.
I