Table of Contents
Advertisement
Available languages
Available languages
1AA. HOSE HANGER: Supports water supply hose.
1BB. STOP POSITION: The saw will stop travel movement
when the speed control lever (1O) is in this position.
The engine will not start unless the Speed Control
Lever (1O) is in the STOP position.
1CC. MANUAL AXLE ADJUSTMENT: Turn bolt to adjust
rear drive axle. Rotating it to the right (CW) makes
saw drive to the right. Left (CCW) makes saw drive
to the left.
1DD. RADIATOR AIR FILTER ELEMENT
FIGURE 2
2A.
BLADE SHAFT BOLT: Use to clamp the diamond
blade between the inner and outer flange. Right
side of saw has left hand threads. Left side of saw
has right hand threads.
2B.
OUTER FLANGE: Use to hold the diamond blade
in position.
2C.
OUTER FLANGE ARBOR: Use to support the
diamond blade.
2D.
LOCkING PIN: Use to prevent the diamond blade
from rotating on the shaft during operation.
2E.
DIAMOND BLADE: Use as the cutting tool for
concrete and asphalt surfaces.
2F.
INNER FLANGE: Inside support used to hold the
diamond blade in position.
2G.
BLADE GUARD NOSE LATCH: Use to latch the
front part of blade guard down.
2H.
BLADE GUARD FRONT: The front part of the
blade guard.
2I.
BLADESHAFT: Supports Blade Flanges and
blade.
FIGURE 3-1
3-1D3
3-1D
3-1D2
3-1A
3-1D1
3-1B
3-1C
3-1J
3-1N
3-1M
3-1G
3-1K
3-1E
3-1F
3-1I
3-1H
3-1L
3-1A. ENGINE GEARBOX: Single Speed Model.
3-1B. WATER CONNECTION: Circulates freshwater
through gearbox to cool it. Water then flows to
the bladeguard.
3-1C. WATER DRAIN VALVE: To drain water from gear-
box: Turn Counterclockwise to open, Clockwise to
close. Drain daily to prevent corrosion or damage
due to freezing temperatures.
3-1D. HOOD LATCH: One latch secures hood in lowered
position. US Model Operation: 1. Press HOOD
LATCH (3-1D3/3-2D3) inward. 2. Raise hood
until HOOD SUPPORT (6H) is engaged & sup-
ports hood. CE Model Operation: 1. Use tool to
loosen Capscrew (3-1D1/3-2D1). 2. Pivot tube latch
(3-1D2/3-2D2) downward. 3. Press HOOD LATCH
(3-1D3/3-2D3) inward. 4. Raise hood until HOOD
SUPPORT (6H) is engaged & supports hood.
3-1E. FLANGE COVER: Guards against FLANGE
contact during operation. Always keep in place!
3-1F. BELT PROTECTOR SHIELD: Keep in place.
3-1G. BLADESHAFT TUBE ASSY: Sealed unit contains
bladeshaft, bearings and shaft seals.
3-1H. TIEDOWN LUGS: Used to tie the saw down
while transporting by vehicle. Not to be used to lift
the saw.
3-1I. ENGINE OIL DRAIN VALVE: Drains engine oil
without use of tools.
3-1J. BELT TENSIONING BOLTS:
3-1k. HORIZONTAL CLAMPING BOLTS:
3-1L. BLADE SHAFT PULLEY:
3-1M. V-BELTS: Set of 4.
3-1N. GEARBOX PULLEY:
Page 47
Hide quick links:
Advertisement
Table of Contents
