Advertisement
NOTICE FOR THE CUSTOMERS IN THE UNITED KINGDOM
A moulded plug complying with BS 1363 is fitted to this equipment for your safety
and convenience.
Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse
approved by ASTA or BSI to BS 1362, (i.e., marked with
be used.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the
fuse cover after you change the fuse. Never use the plug without the fuse cover. If you
should lose the fuse cover, please contact your nearest TOSHIBA TEC service
representative.
WARNING!
1. To prevent fire or shock hazard, do not expose the unit to rain or moisture.
2. To avoid electrical shock, do not open the cover.
3. Refer servicing to qualified personnel only.
4. For indoor use only.
Others
• The model name plate indicating the operating voltage, power consumption, etc.
is located on the bottom of the unit.
• Unplug the unit from the wall outlet if it will not be used for an extended period of
time. To disconnect the cord (mains lead), pull it out by the plug. Never pull the
cord itself.
• Do not operate the unit with a damaged cord or if it has been dropped or damaged.
• Be sure that nothing metallic comes into contact with the metal parts of the unit or
connecting plate. If it does, a short may occur and the unit may be damaged.
• Always keep the metal contacts clean.
• Do not disassemble or convert the unit.
• Do not apply mechanical shock or drop the unit.
• The unit may become warm whilst in use, this is perfectly normal.
• Keep the unit away from AM receivers, because it will disturb AM reception.
• Do not place the unit in a location where it is:
• Temperatures out of the specification
• Dusty or dirty
• Very humid
• Vibrating
If any difficulty should arise, unplug the unit and contact your Authorised TOSHIBA
TEC representative.
Troubleshooting
If you have any problems while using this product, please check the following point first.
If a problem cannot be solved by taking actions described below, unplug the AC adapter and
contact the dealer or an authorized TOSHIBA TEC service representative for assistance.
Symptom
• The AC adapter is not connected to the printer completely.
The power is not supplied even if the
⇒Firmly connect the AC adapter to the printer.
power cord is connected to an AC
• The power cord is not connected to the AC adapter completely.
outlet.
⇒Firmly connect the power cord to the AC
(
is not displayed.)
• The power cord is not connected to the AC outlet completely.
⇒Firmly connect the power cord to the AC outlet.
• A power failure
⇒Please wait until the power is recovered.
• Power is not supplied to the AC outlet.
⇒Test with other electric appliances. If the power is not
• The fuse or breaker of the building has blown out.
⇒ Check the fuse and the breaker.
• The printer is not in stand-by.
⇒The external power source symbol is not displayed while the
• The battery pack is not loaded in the printer.
The CHARGE lamp does not light up.
⇒Load a battery pack in the printer.
• The battery pack loaded in the printer has been fully charged.
⇒A fully charged battery pack is not charged, so
• The ambient temperature or the battery pack temperature does
not fall within the operable temperature range.
⇒Charge the battery pack within 0ºC to 40ºC. A
Specifications
Type:
B-EP800-AC-QM-R (Model: 0225A1950)
Input voltage:
100 to 240V AC, 50/60 Hz
Output voltage:
DC19V, 2.63A
Application:
TOSHIBA Portable Printer B-EP2DL/ B-EP4DL Series
Operating temperature:
0°C to 40°C (32°F to 104°F)
Operating humidity:
20 to 80% (No condensation)
Storage temperature:
-20°C to 70°C (-4°F to 158°F)
Storage humidity:
10 to 90% (No condensation)
Dimensions:
98 x 42 x 29.2mm (L/W/H)
(3.86 x 1.65 x 1.15 inches) (Excluding the projecting parts)
Weight:
250g (8.8 oz)
Accessories:
Owner's Manual x 1
NOTE: Design and specifications are subject to change without notice.
or
4
Cause and resolution
adapter.
supplied to the AC outlet, please consult the nearest power
company.
printer is not in the stand-by state.
the CHARGE lamp does not light up.
battery charge may not be started outside this
range.
6
Before using this unit:
Please follow the instructions below to use the B-EP800-AC-QM-R correctly.
• The B-EP800-AC-QM-R is an AC adapter designed for charging the battery pack
loaded in the B-EP2DL/B-EP4DL series portable printers, not for directly supplying
the power to the B-EP2DL/B-EP4DL series portable printers.
mark) must
This product and the AC adapter supplied with the B-EP800-CHG-QM-R Battery
Charger are the same product.
• DO NOT connect this AC adapter to any devices other than the B-EP2DL/B-
EP4DL series portable printer.
arising from a connection to other devices.
• Before connecting this AC adapter to the printer, please make sure that the
battery pack is in the printer. We are not responsible for any results due to a
failure to do so.
Connecting the AC Adapter to the Printer
When charging the battery pack loaded in the B-EP2DL/B-EP4DL series portable
printer, use the following procedure to connect the AC adapter to the printer.
For how to check the charge status, please refer to the Owner's Manual of the B-
EP2DL/B-EP4DL series portable printer.
1. Make sure that the battery pack is in the printer.
2. Connect the AC adapter to the DCIN connector of the printer.
3. Connect the power cord to an AC outlet.
4. When the AC adapter is plugged in, the external power source symbol (
displayed on the printer's LCD, and charging starts. Whether the battery charge
is required or not is automatically determined by the printer.
5. When the charging is completed, unplug the power cord from the AC outlet and
disconnect the AC adapter from the printer.
NOTE:
Charging time may differ
depending on the condition of the
battery pack or the operating
temperature.
When purchasing the power cord:
Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following
standard from your authorized TOSHIBA TEC representative.
Country
Australia
Austria
Belgium
Canada
Denmark
Finland
France
1. For use with 100 – 125 Vac mains power supply, please select a power cord rated Min. 125V, 10A.
2. For use with 200 – 240 Vac mains power supply, please select a power cord rated Min. 250V.
3. Please select a power cord with the length of 2m or less.
4. The power cord plug connected to the AC adapter must be able to be inserted to an ICE-320-C6 inlet. Refer to
the following figure for the shape.
Country/Region
Power Cord
Rated (Min.)
Type
Conductor size
(Min.)
Plug Configuration
(locally approved
type)
Rated (Min.)
*1: At least, 125% of the rated current of the product.
We assume no responsibility for any results
Portable Printer
DCIN Connector
5
Certification
Agency
Country
Agency
Certification mark
mark
SAA
Germany
VDE
OVE
Ireland
NSAI
CEBEC
Italy
IMQ
CSA
Japan
METI
DEMKO
Netherlands
KEMA
FEI
Norway
NEMKO
UTE
Spain
AEE
Power Cord Instruction
United
North America
Europe
Kingdom
125V, 10A
250V
250V
SVT
H05VV-F
H05VV-F
2
No. 3/18AWG
3 x 0.75 mm
3 x 0.75 mm
125V, 10A
250V, 10A
250V, *1
7
)
AC outlet
Power Plug
Power Cord
AC Adapter
Plug
(As of August 2008)
Country
Agency
Certification mark
Sweden
SEMKKO
Switzerland
SEV
UK
ASTA
UK
BSI
U.S.A.
UL
Europe
HAR
China
CCC
Australia
China
250V
250V
AS3191 approved,
GB5023
Light or Ordinary Duty type
2
2
2
3 x 0.75 mm
3 x 0.75 mm
250V, *1
250V, *1
is
Advertisement
