Specifications; Standard Accessories; Prior To Operation; Practical Operating Procedures - Hitachi SV 12V Handling Instructions Manual

SPECIFICATIONS

Model
Voltage (by areas)*
Power Input
No-load speed
Diam. of Orbit
Sanding pad size
Sanding paper size
Weight (without cord)
*Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

Sanding paper ............................................................ 1
Dust bag (for model SV12V, SV12SD) ...................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
1. Sanding paper
Perforated sanding paper for model SV12V, SV12SD
Non-perforated sanding paper for model SV12SE
Grain: AA40, AA60, AA80, AA100, AA120, AA150,
AA180, AA220, AA240
(1) Standard Type (Perforated or non-Perforated), 114 ×
280 mm
(2) Pressure Sensitive Type (Perforated or non-
Perforated), 114 × 228 mm
2. Magic Pad (Pressure Sensitive Type), 114 × 228 mm
(1) Perforated Pad (for model SV12V, SV12SD)
(2) Non-Perforated Pad (for model SV12SE)
3. Cleaner Adaptor (for model SV12V, SV12SD)
4. Punch plate (for model SV12V, SV12SD)
Optional accessories are subject to change without notice.
APPLICATIONS
Finish polishing of woodwork surfaces
Sanding surfaces of woodwork or sheet metal prior
to painting, etc.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF positon. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
SV12V
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
–1
4000 - 10000min
114 mm × 228 mm
114 mm × 280 mm
2.8 kg
4. Attaching sanding paper
(Start at Switch handle's side)
(1) Open paper holder by turning the clamping lever
(Fig. 1).
(2) Place the sander as shown in Fig. 2. Insert the sanding
paper between the paper holder and the bottom plate
until it can go no further.
(3) Match the width of the sanding paper with the width
of the pad.
Return the clamping lever to its original position to
secure the sanding paper.
(4) When using perforated sanding paper.
To secure the other end of the sanding paper, pull the
sanding paper while aligning the holes of the sanding
paper with the holes of the pad.
(5) When using non-perforated sanding paper.
Align the sanding paper on the pad and pull the
sanding paper to secure the other end.
CAUTION
(1) After mounting the sanding paper, return the
clamping lever to its original position.
(2) The sanding paper must be precisely attached on the
pad, ensuring that there is ample tension (leaving no
slack). Loosely attached sanding paper could result
in unevenly sanded surfaces and/or damage to the
sanding paper itself.
5. Installing and removing the dust bag. (for models
SV12V and SV12SD)
(1) InstaIIation
As shown in Fig. 4, hold the dust gate and push in the
dust bag into the frame's dust bag holder.
(2) Removal
As shown in Fig. 5, push the dust gate's tab hard and
remove the dust bag from the frame.

PRACTICAL OPERATING PROCEDURES

CAUTION
Never apply water or grinding fluid when sanding.
This could result in electrical shok.
1. Switching the sander ON and OFF
By pulling the trigger and pushing the stopper, the
switch will remain ON even when the trigger is
released, promoting continuous, efficient operation.
By pulling the trigger again, the stopper is released
and the switch is turned OFF.
SV12SD SV12SE
300W
–1
10000min
2.4 mm
2.8 kg
English
2.6 kg
6